Normy

Obsah

ČSN EN IEC 60939-3 ed. 2 This part of IEC 60939 covers passive filters used to attenuate unwanted radio-frequency signals (such as noise or interference) generated from electromagnetic sources. Both single and multi-channel filters within one enclosure or which are built on a printed circuit board forming a compact entity are included within the scope of this document. Filters constructed of capacitive elements where the inductance is inherent in the construction of the filter are within the scope of this document. Similarly, filters constructed of inductive elements where the capacitance is inherent in the construction of the filter are also within the scope of this document. It is up to the manufacturer to state whether a given component is to be designed as a capacitor, an inductor or a filter. Filters can include also other components such as resistors and/or varistors or similar components. This document applies to passive filter units for electromagnetic interference suppression for which safety tests are appropriate. This implies that filters specified according to this document will either be connected to mains supplies, when compliance with the mandatory tests of Table B.1 is necessary, or used in other circuit positions where the equipment specification specifies that some or all of these safety tests are required. This document applies to passive filter units, which will be connected to an AC mains or other supply (DC or AC) with a nominal voltage not exceeding 1 000 V AC, with a nominal frequency not exceeding 400 Hz, or 1 500 V DC. NOTE - For AC use, IEC 60384-14 applies to capacitors which will be connected to AC mains with a nominal frequency not exceeding 100 Hz. This document covers appliance filters (US) but does not cover facility filters, cord-connected filters or direct plug-in filters. These other filters will be covered by another sectional specification.

Obsah

ČSN EN IEC 60118-0 ed. 2 Tato část IEC 60118 uvádí doporučení pro měření provozních vlastností sluchadel s vedením zvuku vzduchem, založené na měření s využitím akustické spojky nebo simulátoru uzavřeného ucha. Tento dokument je možné použít při měření a hodnocení elektroakustických vlastností sluchadel, na-příklad při typovém zkoušení a pro stanovení údajů do technické dokumentace od výrobce. Tento dokument je možné použít také při měření provozních vlastností sluchadel pro účely zajištění kvality výroby, zásobování a dodávání sluchadel. Výsledky získané metodami stanovenými v tomto dokumentu budou vyjadřovat vlastnosti za podmí-nek měření a mohou se podstatně lišit od provozních vlastností sluchadel za skutečných podmínek použití. Tento dokument využívá primárně akustickou spojku v souladu s IEC 60318-5, která je určena pouze k zatížení sluchadla stanovenou akustickou impedancí a není určena k reprodukování akustického tlaku v uchu osoby. Při měřeních reflektujících výstupní hladinu v normálním lidské uchu je možné použít simulátor uzavřeného ucha v souladu s IEC 60318-4. Při měřeních v rozšířeném rozsahu vysokých kmitočtů a sluchadel vložených hluboko do zvukovodu je možné použít akustickou spojku v souladu s IEC 60318-8. Tento dokument pokrývá také měření sluchadel s neakustickými vstupy, jako je bezdrátový, indukční nebo elektrický vstup. Tento dokument nepokrývá měření provozních vlastností sluchadel za simulovaných pracovních pod-mínek in situ, pro která je možné použít IEC 60118-8. Tento dokument nepokrývá měření v obvyklých uživatelských nastaveních s využitím simulovaného řečového signálu, pro která je možné použití IEC 60118-15.

Obsah

ČSN EN 10088-1 Dokument uvádí přehled chemického složení korozivzdorných ocelí, které jsou dále rozděleny podle jejich hlavních vlastností na oceli odolné korozi, oceli žáruvzdorné, oceli žáropevné.

Obsah

ČSN EN IEC 61223-3-8 This part of IEC 61223 applies to evaluation of the imaging performance and related quality control parameters of X-ray equipment for radiography and radioscopy that conform to IEC 60601-2-54:2022 or IEC 60601-2-43:2022. This document applies to the evaluation of the imaging performance of the entire imaging chain from image acquisition, image processing and image display.

Obsah

ČSN EN ISO 56008 This document provides guidance for the definition, implementation, evaluation, and improvement of the measurements necessary to effectively manage innovation activities in an organization. It establishes the fundamentals of innovation operation measurements and guides their application towards four areas: - measurements for establishing and launching innovation initiatives; - measurements for innovation processes; - measurements for innovation initiatives; - measurements of innovation portfolios. This document is applicable to: - organizations that are seeking to define and implement an innovation operations measurement approach; - organizations and interested parties seeking to improve the areas of accountability, transparency, and evidence-based assessment of innovation operations; - customers, investors, and other interested parties, seeking confidence in the organization's innovation operations management and its results; - providers of training in innovation operations and measurements, including assessment of and consultancy for achieving results; - experts in innovation operations evaluation and impact assessment, favoring the use of a harmonized international guidance standard; - innovation policy makers and program managers who are looking to obtain evidence of progress and desired outcomes of innovation activities supported through public policies and programs. All of the guidance provided within this document is generic and intended to be applicable to: - all types of organizations regardless of sector or size, whether they be private, public, not-for-profit, governmental or societal; - all types of innovations (e.g. product, service, process, model, and method) ranging from incremental to radical; - all types of time horizons, from short-term to long-term evaluation and measurement.

Obsah

ČSN EN IEC 61784-5-8 ed. 3 This part of IEC 61784-5 specifies the installation profiles for CPF 8 (CC-LinkTM). The installation profiles are specified in the annexes. These annexes are read in conjunction with IEC 61918:2018, IEC 61918:2018/AMD1:2022 and IEC 61918:2018/AMD2:2024.

Obsah

ČSN EN IEC 61162-450 ed. 3 This part of IEC 61162 specifies interface requirements and methods of test for high speed communication between shipboard navigation and radiocommunication equipment as well as between such systems and other ship systems that need to communicate with navigation and radio-communication equipment. This document is based on the application of an appropriate suite of existing international standards to provide a framework for implementing data transfer between devices on a shipboard Ethernet network. This document specifies an Ethernet based bus type network where any listener can receive messages from any sender with the following properties. - This document includes provisions for multicast distribution of information formatted according to IEC 61162-1, for example position fixes and other measurements, as well as provisions for transmission of general data blocks (binary file), for example between radar and VDR, and also includes provisions for multicast distribution of information formatted according to IEC 61162-3, for example position fixes and other measurements. - This document is limited to protocols for equipment (network nodes) connected to a single Ethernet network consisting only of OSI level one or two devices and cables (network infrastructure). - This document provides requirements only for equipment interfaces. By specifying protocols for transmission of IEC 61162-1 sentences, IEC 61162-3 PGN messages and general binary file data, these requirements will guarantee interoperability between equipment implementing this document as well as a certain level of safe behaviour of the equipment itself. - This document permits equipment using other protocols than those specified in this document to share a network infrastructure, provided that it is supplied with interfaces which satisfy the requirements described for ONF. - This document includes provisions for filtering of the network traffic in order to limit the amount of traffic to manageable level for each individual equipment. This document does not contain any system requirements other than the ones that can be inferred from the sum of individual equipment requirements. An associated standard, IEC 61162-460, further addresses system requirements.

Obsah

ČSN EN 10088-3 Tento dokument specifikuje technické dodací podmínky pro polotovary, za tepla nebo za studena tvářených tyčí, válcovaných drátů, profilů a lesklých výrobků z běžných nebo speciálních značek korozivzdorných ocelí pro obecné použití. POZNÁMKA - Obecné účely zahrnují i používání korozivzdorných ocelí v kontaktu s potravinami. Pokud v tomto dokumentu není stanoveno jinak, platí k údajům této evropské normy stanovené obecné technické dodací podmínky v EN 10021. Tento dokument neplatí pro součásti, které jsou vyrobeny dalším zpracováním, zhotoveny ve formách výrobků výše uvedených tvarů, s charakteristickými rysy změněnými následkem takového dalšího zpracování.

Obsah

ČSN EN 15941 This document specifies the data quality assessment and selection of data for Environmental Product Declarations (EPD) according to the core product category rules of EN 15804 and for the environmental performance assessment of buildings according to EN 15978 in a consistent way. It can also be used to assess and select data for the environmental assessment of civil engineering works according to EN 17472. It defines data quality requirements with respect to temporal, technological and geographical representativeness for the data used to calculate the Life Cycle Assessment (LCA) based indicator results of the EPD and for construction works when applying EPD, life cycle inventory data or other LCA based information, and gives guidance for the generation of a hierarchy to support the selection of the most appropriate data regarding data quality. It also addresses the reporting of data quality at product and building level.

Obsah

ČSN EN 1992-1-2 ed. 2 (73 1201) (1) This document deals with the design of concrete structures for the accidental situation of fire exposure and is intended to be used in conjunction with EN 1992-1-1 and EN 1991-1-2:-1. This document identifies differences from, or supplements to, normal temperature design. (2) This document applies to concrete structures required to fulfil a loadbearing function, separating function, insulation function or all of them. (3) This document gives principles and application rules for the design of structures for specified requirements in respect of the aforementioned functions and the levels of performance. (4) This document applies to structures, or parts of structures, that are within the scope of EN 1992-1-1 and are designed accordingly.

Obsah

ČSN CLC IEC/TS 61851-3-4 Tato část IEC 61851, která je technickou specifikací, se vztahuje na komunikaci CANopen pro přenos elektrické energie vodivým propojením mezi napájecí sítí a elektrickým silničním vozidlem nebo přemístitelným dobíjecím systémem pro ukládání energie (RESS) nebo palubními systémy elektrického silničního vozidla pro ukládání energie (RESS). Systém hospodaření s energií (EMS) pro řízení přenosu energie mezi bateriovými systémy a jednotkami měniče napětí (VCU) zajišťuje komunikaci pro všechna zařízení, která se mohou podílet na řízení spotřeby energie.

Obsah

ČSN EN 1993-1-2 This document provides rules for the design of steel structures for the accidental situation of fire exposure. This Part of EN 1993 only identifies differences from, or supplements to, normal temperature design. This document applies to steel structures required to fulfil a loadbearing function. This document does not include rules for separating function. This document gives principles and application rules for the design of structures for specified require-ments in respect of the aforementioned loadbearing function and the levels of performance. This document applies to structures, or parts of structures, that are within the scope of EN 1993-1-1 and are designed accordingly. This document is intended to be used in conjunction with EN 1991-1-2, EN 1993-1-1, EN 1993-1-3, EN 1993-1-4, EN 1993-1-5, EN 1993-1-6, EN 1993-1-7, EN 1993-1-8, EN 1993-1-11, EN 1993-1-13 or EN 1993-1-14. In this document, carbon steel is meant when the term steel is used. Only in Annex C stainless steel is addressed. Unless specifically stated, EN 1990, EN 1991(all parts) and EN 1993-1-1 apply. The design methods given in this document are applicable if - the execution quality is as specified in EN 1090-2 and/or EN 1090-4, and - the construction materials and products used are as specified in EN 1993-1-1:2022, Table 5.1 and Table 5.2 and in EN 1993-1-3:2024, Table 5.1 and Table 5.2, or in the relevant material and product specifications. In addition to the general assumptions of EN 1990 the following assumptions apply: - the choice of the relevant design fire scenario is made by appropriate qualified and experienced personnel, or is given by the relevant national regulation; - any fire protection measure taken into account in the design will be adequately maintained.