Normy

Obsah

ČSN EN 12516-1+A1 This European Standard specifies the tabulation method for determining the wall thickness of valve bodies, bonnets and covers with essentially circular cross-section made in forged, cast or fabricated steel.

Obsah

ČSN EN IEC 61918 ed. 3 This document specifies basic requirements for the installation of media for communication networks within and between the automation islands, of industrial sites. This document covers balanced and optical fibre cabling. It also covers the cabling infrastructure for wireless media, but not the wireless media itself. Additional media are covered in IEC 61784-5 (all parts). This document is a companion standard to the communication networks of the industrial automation islands and especially to the communication networks specified in IEC 61158 (all parts) and IEC 61784 (all parts). In addition, this document covers the connection between the generic telecommunications cabling specified in ISO/IEC 11801-3 and the specific communication cabling of an automation island, where an automation outlet (AO) replaces the telecommunication outlet (TO) of ISO/IEC 11801-3. This document provides guidelines that cope with the critical aspects of the industrial automation area (safety, security and environmental aspects such as mechanical, liquid, particulate, climatic, chemicals and electromagnetic interference). This document does not recognise implementations of power distribution with or through Ethernet balanced cabling systems. This document deals with the roles of planner, installer, verifier, and acceptance test personnel, administration and maintenance personnel and specifies the relevant responsibilities and/or gives guidance.

Obsah

ČSN EN ISO 52016-1 Tento dokument specifikuje výpočtové metody pro posuzování: potřeby (citelné) energie na vytápění a chlazení na základě hodinových a měsíčních výpočtů; potřeby latentní energie na zvlhčování (odvlhčování) na základě hodinových a měsíčních výpočtů; vnitřní teploty na základě hodinových výpočtů; citelného výkonu na vytápění a chlazení na základě hodinových výpočtů; vlhkostního a latentního tepelného výkonu pro zvlhčování (odvlhčování) na základě hodinových výpočtů; návrhového citelného výkonu na vytápění nebo chlazení a návrhového latentního tepelného výkonu při použití hodinového výpočtového intervalu; podmínek přívodního vzduchu k zajištění potřebného zvlhčování a odvlhčování. Výpočtové metody lze použít pro obytné nebo neobytné budovy nebo jejich části označované jako "budova" nebo "posuzovaný objekt" (předmět posuzování). Tento dokument také obsahuje specifikace týkající se posuzování tepelných zón v budově nebo v části budovy. Výpočty se provádějí pro jednotlivé tepelné zóny. Ve výpočtech lze tepelné zóny považovat za tepelně propojené nebo nikoliv. Výpočtové metody byly vyvinuty pro výpočet základních energetických výkonů a potřeb energie, bez interakce se specifickými technickými systémy budovy, a pro výpočet pro systém specifických energetických výkonů a potřeb energie včetně interakce se specifickými systémy. Hodinové výpočtové postupy lze také použít jako základ pro výpočty při rozsáhlejších možnostech regulace systémů. Tento dokument platí pro budovy ve fázi navrhování, dokončené nové budovy a existující budovy ve fázi užívání.

Obsah

ČSN EN 1992-1-1 ed. 2 (73 1201) (1)P Eurokód 2 se používá pro navrhování konstrukcí pozemních a inženýrských staveb z prostého, železového a předpjatého betonu. Splňuje zásady a požadavky týkající se bezpečnosti a použitelnosti konstrukcí a zásady pro jejich navrhování a prověřování, které jsou dány v EN 1990 Zásady navrhování konstrukcí. (2)P Eurokód 2 se týká pouze požadavků na únosnost, použitelnost, trvanlivost a požární odolnost betonových konstrukcí. Další požadavky, např. požadavky na tepelnou a zvukovou izolaci, se zde neuvažují. (3) Předpokládá se, že Eurokód 2 bude používán společně s těmito dokumenty: EN 1990 Eurokód: Zásady navrhování konstrukcí EN 1991 Eurokód 1: Zatížení konstrukcí hEN´s Stavební výrobky souvisící s betonovými konstrukcemi ENV 13670 Provádění betonových konstrukcí EN 1997 Eurokód 7: Navrhování geotechnických konstrukcí EN 1998 Eurokód 8: Navrhování konstrukcí odolných proti zemětřesení, pokud jsou betonové konstrukce stavěny v seismických oblastech. (4)P Eurokód 2 se dělí na následující části: Část 1-1: Obecná pravidla a pravidla pro pozemní stavby Část 1-2: Navrhování konstrukcí na účinky požáru Část 2: Železobetonové a předpjaté betonové mosty Část 3: Nádrže na kapaliny a zásobníky

Obsah

ČSN EN ISO 19904-1 This document provides requirements and guidance for the structural design and/or assessment of floating offshore platforms used by the petroleum and natural gas industries to support the following functions: - production; - storage and/or offloading; - drilling and production; - production, storage and offloading; - drilling, production, storage and offloading. NOTE 1 Floating offshore platforms are often referred to using a variety of abbreviations, e.g. FPS, FSU, FPSO (see Clauses 3 and 4), in accordance with their intended mission. NOTE 2 In this document, the term "floating structure", sometimes shortened to "structure", is used as a generic term to indicate the structural systems of any member of the classes of platforms defined above. NOTE 3 In some cases, floating platforms are designated as "early production platforms". This term relates merely to an asset development strategy. For the purposes of this document, the term "production" includes "early production". This document is not applicable to the structural systems of mobile offshore units (MOUs). These include, among others, the following: - floating structures intended primarily to perform drilling and/or well intervention operations (often referred to as MODUs), even when used for extended well test operations; - floating structures used for offshore construction operations (e.g. crane barges or pipelay barges), for temporary or permanent offshore living quarters (floatels), or for transport of equipment or products (e.g. transportation barges, cargo barges), for which structures reference is made to relevant recognized classification society (RCS) rules. This document is applicable to all possible life-cycle stages of the structures defined above, such as: - design, construction and installation of new structures, including requirements for inspection, integrity management and future removal, - structural integrity management covering inspection and assessment of structures in-service, and - conversion of structures for different use (e.g. a tanker converted to a production platform) or re use at different locations. The following types of floating structure are explicitly considered within the context of this document: a) ship-shaped structures and barges; b) semi-submersibles; c) spars; d) shallow-draught cylindrical structures. In addition to the structural types listed above, this document covers other floating platforms intended to perform the above functions, consisting of partially submerged buoyant hulls made up of any combination of plated and space frame components. These other structures can have a great range of variability in geometry and structural forms (e.g. tension leg platforms) and, therefore, can be only partly covered by the requirements of this document. In other cases, specific requirements stated in this document can be found not to apply to all or part of a structure under consideration. NOTE 4 Requirements for topsides structures are presented in ISO 19901-3. In the above cases, conformity with this document requires the design to be based upon its underpinning principles and to achieve a level of safety equivalent, or superior, to the level implicit in it. NOTE 5 The speed of evolution of offshore technology often far exceeds the pace at which the industry achieves substantial agreement on innovation in structural concepts, structural shapes or forms, structural components and associated analysis and design practices, which are continuously refined and enhanced. On the other hand, International Standards can only capture explicit industry consensus, which requires maturation and acceptance of new ideas. Consequently, advanced structural concepts can, in some cases, only be partly covered by the requirements of this document. This document is applicable to steel floating structures. The principles documented herein are, however, considered to be generally applicable to structures fabricated in materials other than steel.

Obsah

ČSN ETSI EN 300 392-7 V3.5.1 The present document defines the Terrestrial Trunked Radio system (TETRA) supporting Voice plus Data (V+D). It specifies the air interface, the inter-working between TETRA systems and to other systems via gateways, the terminal equipment interface on the mobile station, the connection of line stations to the infrastructure, the security aspects in TETRA networks, the management services offered to the operator, the performance objectives, and the supplementary services that come in addition to the basic and teleservices. The present part describes the security mechanisms in TETRA V+D. It provides mechanisms for confidentiality of control signalling and user speech and data at the air interface, authentication and key management mechanisms for the air interface and for the Inter-System Interface (ISI). Clause 4 describes the authentication and key management mechanisms for the TETRA air interface. The following two authentication services have been specified for the air-interface in ETSI ETR 086-3 [i.3], based on a threat analysis: - authentication of an MS by the TETRA infrastructure; - authentication of the TETRA infrastructure by an MS. Clause 5 describes the mechanisms and protocol for enable and disable of both the mobile station equipment and the mobile station user's subscription. Air interface encryption may be provided as an option in TETRA. Where employed, clause 6 describes the confidentiality mechanisms using encryption on the air interface, for circuit mode speech, circuit mode data, packet data and control information. Clause 6 describes both encryption mechanisms and mobility procedures. It also details the protocol concerning control of encryption at the air interface. The present document does not address the detail handling of protocol errors or any protocol mechanisms when TETRA is operating in a degraded mode. These issues are implementation specific and therefore fall outside the scope of the TETRA standardization effort. The detail description of the Authentication Centre is outside the scope of the present document.

Obsah

ČSN ETSI EN 300 468 V1.16.1 The present document specifies the Service Information (SI) data which forms a part of DVB bitstreams, in order that the user can be provided with information to assist in selection of services and/or events within the bitstream, and so that the Integrated Receiver Decoder (IRD) can automatically configure itself for the selected service. SI data for automatic configuration is mostly specified within ISO/IEC 13818 1 [15] as Program Specific Information (PSI). The present document specifies additional data which complements the PSI by providing data to aid automatic tuning of IRDs, and additional information intended for display to the user. The manner of presentation of the information is not specified in the present document, and IRD manufacturers have freedom to choose appropriate presentation methods. It is expected that Electronic Programme Guides (EPGs) will be a feature of Digital TV transmissions. The definition of an EPG is outside the scope of the present document (i.e. the SI specification), but the data contained within the SI specified in the present document may be used as the basis for an EPG. Rules of operation for the implementation of the present document are specified in ETSI TS 101 211 [i.1].

Obsah

ČSN EN 17082 This document specifies the requirements and test methods for the safety and efficiency of gas fired air heaters with or without a fan to assist the transportation of combustion air and/or flue gases, hereafter referred to as "appliances". This document also applies to warm air heaters having forced draught burners. This document applies to Type A2, A3 appliances, with an input not exceeding 300 kW (net CV basis), intended for non-domestic use. This document also applies to Type B11, B11AS, B11BS, B12, B12AS, B12BS, B13, B13AS, B13BS, B14, B14AS, B14BS, B22, B23, B41, B41AS, B41BS, B42, B42AS, B42BS, B43, B43AS, B43BS, B44, B44AS, B44BS, B52, B53, C11, C12, C13, C21, C31, C32, C33, C41, C62 and C63 appliances with an input not exceeding 300 kW (net CV basis), intended for domestic and non-domestic use. Provision of the heated air may be by means of ducting. This document does not apply to: a) dual purpose air conditioning appliances (heating and cooling); b) appliances where the air is heated by an intermediate fluid; c) portable or transportable forced convection appliances; d) appliances fitted with manual or automatic means of adjusting the combustion products evacuation by means of flue dampers; e) appliances having multiple heating units with a single draught diverter; f) appliances fitted with more than one flue outlet; g) appliances fitted with gas boosters; h) C21 and C41 appliances for 3rd family gases. NOTE - For C41 appliances, see all requirements and test methods that are valid for C21 appliances, unless otherwise stated. This document is not intended to cover appliances projected for connection to gas grids where the quality of the distributed gas is likely to vary to a large extent over the lifetime of the appliance. This document is applicable to appliances which are intended to be type tested.

Obsah

ČSN EN 12845+A1 (38 9211) This European Standard specifies requirements and gives recommendations for the design, installation and maintenance of fixed fire sprinkler systems in buildings and industrial plants, and particular requirements for sprinkler systems that are integral to measures for the protection of life. This European Standard covers only the types of sprinkler specified in EN 12259-1 (see Annex L). The requirements and recommendations of this European Standard are also applicable to any addition, extension, repair or other modification to a sprinkler system. They are not applicable to water spray or deluge systems. It covers the classification of hazards, provision of water supplies, components to be used, installation and testing of the system, maintenance, and the extension of existing systems, and identifies construction details of buildings which are the minimum necessary for satisfactory performance of sprinkler systems complying with this European Standard. This European Standard does not cover water supplies to systems other than sprinklers. Its requirements can be used as guidance for other fixed firefighting extinguishing systems, provided that any specific requirements for other firefighting extinguishing supplies are taken into account. This European Standard is intended for use by those concerned with purchasing, designing, installing, testing, inspecting, approving, operating and maintaining automatic sprinkler systems, in order that such equipment will function as intended throughout its life. This European Standard is intended only for fixed fire sprinkler systems in buildings and other premises on land. Although the general principles might well apply to other uses (e.g. maritime use). For these other uses additional considerations should be taken into account. The requirements are not valid for automatic sprinkler systems on ships, in aircraft, on vehicles and mobile fire appliances or for below ground systems in the mining industry. Sprinkler system design deviations might be allowed when such deviations have been shown to provide a level of protection at least equivalent to this European Standard, for example by means of full-scale fire testing where appropriate, and where the design criteria have been fully documented.

Obsah

ČSN ETSI EN 300 175-8 V2.8.1 The present document is one of the parts of the specification of the Digital Enhanced Cordless Telecommunications (DECT) Common Interface (CI). This part of the DECT CI specifies the speech and audio coding and transmission requirements. In order to ensure satisfactory interworking of different portable and fixed units, it is necessary to specify the transmission performance of the analog information over the digital link. This requires not only use of a common speech algorithm, but also standardization of frequency responses, reference speech levels (or loudness) at the air interface and various other parameters. The present document applies to DECT equipment which includes all the necessary functions to provide real time two way speech conversation and stereo audio transmission. Several speech services are defined in the present document, including conventional 3,1 kHz telephony, wideband 7 kHz voice transmission, super-wideband 14 kHz and fullband 20 kHz service. DECT Fixed part providing such services may be connected to the public circuit switched (PSTN/ISDN) network, to private networks or to the Voice over Internet Protocol (VoIP) network. Tethered fixed point local loop applications are not required to comply with the requirements of the present document. For the DECT systems which connect to the Public Switched Telephone Network (PSTN) via an analog interface, the additional requirements, which are implemented in the FP, have as much as possible been aligned with ETSI TBR 038 [29]. A summary of the control and the use of the DECT echo control functions, to guide on need for options to manufacturers and installers, is found in annex A. Information concerning test methods can be found in ETSI EN 300 176-1 [9] and ETSI EN 300 176-2 [10] (previously covered by ETSI TBR 010 [i.5]). The test methods take into account that DECT is a digital system. The present document includes New Generation DECT, a further development of the DECT standard introducing wideband speech, improved data services, new slot types and other technical enhancements. In addition, the present document includes DECT Evolution, providing SWB and FB speech and audio capabilities and a new speech coding algorithm for NB and WB allowing to increase the audio quality of the NB and WB speech service and improve bandwidth efficiency.

Obsah

ČSN EN 61850-7-3 ed. 2+A1 1.1 General This part of IEC 61850 specifies constructed attribute classes and common data classes related to substation applications. In particular, it specifies: - common data classes for status information, - common data classes for measured information, - common data classes for control, - common data classes for status settings, - common data classes for analogue settings and - attribute types used in these common data classes. This International Standard is applicable to the description of device models and functions of substations and feeder equipment. This International Standard may also be applied, for example, to describe device models and functions for: - substation to substation information exchange, - substation to control centre information exchange, - power plant to control centre information exchange, - information exchange for distributed generation, or - information exchange for metering. 1.2 Namespace name and version This new section is mandatory for any IEC 61850 namespace (as defined by IEC 61850-7-1:2011). The parameters which are identifying this new release of this namespace are: - Namespace Version: 2007 - Namespace Revision: B - Namespace name: "IEC 61850-7-3:2007B" - Namespace release: 3 - Namespace release date: 2019-10-02 1.3 Code Component distribution The Code Component will be available in light and full version: - Full version will contain definition of the whole LNs defined in this standard with the documentation associated and access will be restricted to purchaser of this part - Light version will not contain the documentation but will contain the whole definition of the LNs as per full version, and this light version will be freely accessible on the IEC website for download, but the usage remains under the licensing conditions.

Obsah

ČSN ETSI EN 300 392-3-13 V1.2.1 The present document defines the group call communication of interworking at the Inter-System Interface (ISI) for Terrestrial Trunked Radio system (TETRA) supporting Voice plus Data (V+D). The TETRA V+D interworking - basic operation part defines the interworking between TETRA networks over the corresponding interface: the Inter-System Interface (ISI). It comprises the following sub-parts: - Transport Layer Independent Specification ISI general design [2]; - General Design, PSS1 over E.1 [i.7]; - General Design, SIP/IP [i.8]; - Transport Layer Independent Additional Network Feature - ISI Individual Call (ANF-ISIIC) [3]; - Transport Layer Independent Additional Network Feature Group Call (ANF-ISIGC) (the present document); - Transport Layer Independent Additional Network Feature Short Data service (ANF-ISISD) [i.9]; - Transport Layer Independent Additional Network Feature Mobility Management (ANF-ISIMM) [4]; - Generic Speech Format Implementation [i.10]. The present document is the ANF-ISIGC sub-part 3-13. In analogy with Recommendation ITU T I.130 [i.3], the stage one, stage two and stage three of the three level structure is used to describe the TETRA Inter-System Interface services as provided by European Private or Public Trunked Radio System operators: - Stage 1, is an overall service description, from the service subscriber's and user's standpoint; - Stage 2, identifies the functional capabilities and information flows needed to support the services described in stage 1; and NOTE: The information flows in stage 2 have been drawn as Message Sequence Charts (MSC). - Stage 3, defines the signalling system protocols and functions needed to implement the services described in stage 1. The present document details the Interworking Basic Operation of the Terrestrial Trunked Radio system (TETRA). Specifically the present document details the stage 1 aspects (overall service description) of the ANF-ISIGC as seen from the TETRA Switching and Maintenance Infrastructure point of view at the Inter-System Interface (ISI). It details the stage 2 aspects (functional partitioning) of ANF-ISIGC which includes the identification of the functional entities and the flows between them, and finally it details the stage 3 signalling protocols for the ANF-ISIGC services, i.e. the protocols at the relevant reference points between the functional entities defined in stage 2. The ANF-ISIGC service specifies: - TETRA Group Call Clear Speech over the ISI, acknowledged and unacknowledged; - TETRA Group Call End-to-End Encrypted Speech over the ISI; - TETRA Group Call Circuit Mode one slot data over the ISI; - TETRA Group Call Circuit Mode one slot End-to-End Encrypted data over the ISI; - TETRA Group Call Circuit Mode N × 2,4 kbit/s, N × 4,8 kbit/s or N × 7,2 kbit/s data, with N = 2, 3 or 4; - TETRA Group Call Circuit Mode N × 2,4 kbit/s N × 4,8 kbit/s or N × 7,2 kbit/s End-to-End Encrypted data, with N = 2, 3 or 4.