Normy

Obsah

ČSN EN 1116 Tato evropská norma stanoví koordinované rozměry pro kuchyňské skříňky, pracovní desky, krycí panely, kuchyňská čela a ozdobné panely a také pro kuchyňské spotřebiče (bílé zboží a trouby) a další instalační prvky, např. dřezy (zkráceně "vybavení"). Tato norma určuje výšku, šířku, hloubku a prostor pro zabudování vybavení do kuchyňských skříněk. Tato evropská norma se nevztahuje na komerčně užívané kuchyně (např. v hotelích, restauracích).

Obsah

ČSN EN ISO 17115 This document defines the requirements for the design and manufacture of aluminium and steel trusses used in the entertainment industry. This document does not cover individual, separate rigging hardware like shackles, wire ropes, slings and other lifting accessories.

Obsah

ČSN EN ISO 18314-1 This part of ISO 18314 specifies the method for determining the colour coordinates of a paint film. This method is only applicable to paint films that appear to be uniformly of one colour, i.e. monochromatic, when examined with normal vision. Paint films that do not completely hide a non-transparent substrate represent an opaque system and can be measured by using the procedure in this part of ISO 18314. Luminescent paint films, transparent paint films, and translucent paint films (for example for display or lamp glass), retroreflecting paint films (for example for traffic signs), and metallic paint films are outside the scope of this part of ISO 18314.

Obsah

ČSN EN ISO 11124-4 This document specifies requirements for 12 grades of low-carbon cast-steel shot abrasive, as supplied for blast-cleaning processes. Values are specified for hardness, density, defect/structural requirements and chemical composition. The requirements specified in this document apply to abrasives supplied in the "new" condition only. They do not apply to abrasives either during or after use. Test methods for metallic blast-cleaning abrasives are given in the various parts of ISO 11125. Low-carbon cast-steel shot abrasives are used in both static and site blasting equipment. They are most often selected where a facility exists for recovery and re-use of the abrasive. NOTE 1: Information on commonly referenced national standards for metallic abrasives and their approximate relationship with ISO 11124 is given in Annex A. NOTE 2: Although this document has been developed specifically to meet requirements for preparation of steelwork, the properties specified will generally be appropriate for use when preparing other material surfaces, or components, using blast-cleaning techniques. These techniques are described in ISO 8504-2.

Obsah

ČSN EN ISO 11124-3 This document specifies requirements for 14 grades of high-carbon cast-steel shot and 11 grades of high-carbon cast-steel grit, as supplied for blast-cleaning processes. Values are specified for hardness, density, defect/structural requirements and chemical composition. The requirements specified in this document apply to abrasives supplied in the "new" condition only. They do not apply to abrasives either during or after use. Test methods for metallic blast-cleaning abrasives are given in the various parts of ISO 11125. High-carbon cast-steel shot and grit are used in both static and site blasting equipment. They are most often selected where a facility exists for the recovery and re-use of the abrasive. NOTE 1: Information on commonly referenced national standards for metallic abrasives and their approximate relationship with ISO 11124 is given in Annex A. NOTE 2: Although this document has been developed specifically to meet requirements for preparation of steelwork, the properties specified will generally be appropriate for use when preparing other material surfaces, or components, using blast-cleaning techniques. These techniques are described in ISO 8504 2.

Obsah

ČSN EN ISO 11124-2 This document specifies requirements for 12 grades of chilled-iron grit abrasives, as supplied for blast-cleaning processes. It specifies ranges of particle sizes, together with corresponding grade designations. Values are specified for hardness, density, defect/structural requirements and chemical composition. The requirements specified in this document apply to abrasives supplied in the "new" condition only. They do not apply to abrasives either during or after use. Test methods for metallic blast-cleaning abrasives are given in the various parts of ISO 11125. Chilled-iron grit abrasives are used in both static and site blasting equipment. They are most often selected where a facility exists for recovery and re-use of the abrasive. NOTE: Although this document has been developed specifically to meet requirements for preparation of steelwork, the properties specified will generally be appropriate for use when preparing other material surfaces, or components, using blast-cleaning techniques. These techniques are described in ISO 8504-2.

Obsah

ČSN EN ISO 11125-6 This document specifies a test method for the determination of foreign matter in metallic blast-cleaning abrasives. The purpose of the test is to establish the level to which the abrasive is contaminated by foreign matter. The level of foreign matter, e.g. oxides and residual metallurgical slag, is determined by magnetic separation. This is one of a number of parts of ISO 11125 dealing with the sampling and testing of metallic abrasives for blast-cleaning. The types of metallic abrasive and requirements on each are contained in the various parts of ISO 11124. The ISO 11124 and ISO 11125 series have been drafted as a coherent set of International Standards on metallic blast-cleaning abrasives. Information on all parts of both series is given in Annex A.

Obsah

ČSN EN ISO 11125-2 This document specifies a test method for the determination of particle size distribution of metallic blast-cleaning abrasives by sieving. This is one of a number of parts of ISO 11125 dealing with the sampling and testing of metallic abrasives for blast-cleaning. The types of metallic abrasive and requirements on each are contained in the various parts of ISO 11124. The ISO 11124 and ISO 11125 series have been drafted as a coherent set of International Standards on metallic blast-cleaning abrasives. Information on all parts of both series is given in Annex A.

Obsah

ČSN EN ISO 11125-4 This document specifies a test method for the determination of the apparent density of metallic blast-cleaning abrasives. The purpose of the test is to establish the soundness of the metallic abrasive. Significant levels of internal shrinkage or hollow particles will reduce the apparent density. This is one of a number of parts of ISO 11125 dealing with the sampling and testing of metallic abrasives for blast-cleaning. The types of metallic abrasive and requirements on each are contained in the various parts of ISO 11124. The ISO 11124 and ISO 11125 series have been drafted as a coherent set of International Standards on metallic blast-cleaning abrasives. Information on all parts of both series is given in Annex A.

Obsah

ČSN EN ISO 11125-3 This document specifies a test method for the determination of the Vickers hardness of metallic blast-cleaning abrasives. This method is not recommended for the testing of particle sizes below 0,3 mm. NOTE: Accurate testing of particles below 0,3 mm (grades S040/G050) is extremely difficult. This is one of a number of parts of ISO 11125 dealing with the sampling and testing of metallic abrasives for blast-cleaning. The types of metallic abrasive and requirements on each are contained in the various parts of ISO 11124. The ISO 11124 and ISO 11125 series have been drafted as a coherent set of International Standards on metallic blast-cleaning abrasives. Information on all parts of both series is given in Annex A.

Obsah

ČSN EN ISO 11126-7 This document specifies requirements for fused aluminium oxide abrasives, as supplied for blast-cleaning processes. It specifies ranges of particle sizes and values for apparent density, bulk density, Mohs hardness, moisture content, conductivity of aqueous extract and water-soluble chlorides. The requirements specified in this document apply to abrasives supplied in the "new" condition only. They do not apply to abrasives either during or after use. Test methods for non-metallic blast-cleaning abrasives are given in the various parts of ISO 11127. NOTE 1: Information on commonly referenced national and international standards is given in Bibliography. NOTE 2: Although this document has been developed specifically to meet requirements for preparation of steelwork, the properties specified will generally be appropriate for use when preparing other material surfaces, or components, using blast-cleaning techniques. These techniques are described in ISO 8504 2.

Obsah

ČSN EN ISO 11126-6 This document specifies requirements for iron and steel slag abrasives, as supplied for blast-cleaning processes. It specifies ranges of particle sizes and values for apparent density, Mohs hardness, moisture content, conductivity of aqueous extract and water-soluble chlorides. The requirements specified in this document apply to abrasives supplied in the "new" condition only. They do not apply to abrasives either during or after use. Test methods for non-metallic blast-cleaning abrasives are given in the various parts of ISO 11127. NOTE: Although this document has been developed specifically to meet requirements for preparation of steelwork, the properties specified will generally be appropriate for use when preparing other material surfaces, or components, using blast-cleaning techniques. These techniques are described in ISO 8504 2.