Normy

Obsah

ČSN EN IEC 63376 This International Standard specifies the functions and the information flows of industrial Facility Energy Management System (FEMS). Generic functions are defined for the FEMS, to enable upgrading traditional Energy Management System (EMS) from visualization of the status of energy consumption to automation of energy management defining a closer relation with other management and control systems. A generic method to classify the FEMS functions will be explained. The information exchange between the FEMS and other systems such as Manufacturing Operations Management (MOM), Manufacturing Execution System (MES) and Enterprise Resource Planning (ERP) will be outlined.

Obsah

ČSN EN ISO 15118-9 This document specifies requirements for the attachment of part-turn actuators, with or without This document specifies conformance tests in the form of an abstract test suite (ATS) for a system under test (SUT) implementing an electric-vehicle or supply-equipment communication controller (EVCC or SECC) with support for WLAN-based high-level communication (HLC) according to ISO 15118-8 and against the background of ISO 15118-1. These conformance tests specify the testing of capabilities and behaviours of an SUT, as well as checking what is observed against the conformance requirements specified in ISO 15118-8 and against what the implementer states the SUT implementation's capabilities are. The capability tests within the ATS check that the observable capabilities of the SUT are in accordance with the static conformance requirements defined in ISO 15118-8. The behaviour tests of the ATS examine an implementation as thoroughly as practical over the full range of dynamic conformance requirements defined in ISO 15118-8 and within the capabilities of the SUT (see NOTE below). A test architecture is described in correspondence to the ATS. The abstract test cases in this document are described leveraging this test architecture and are specified in descriptive tabular format for the ISO/OSI physical and data link layers (layers 1 and 2). In terms of coverage, this document only covers normative sections and requirements in ISO 15118-8. This document can additionally refer to specific tests for requirements on referenced standards (e.g. IEEE, or industry consortia standards, like WiFi Alliance) as long as they are relevant in terms of conformance for implementations according to ISO 15118-8. However, it is explicitly not intended to widen the scope of this conformance specification to such external standards, if it is not technically necessary for the purpose of conformance testing for ISO 15118-8. Furthermore, the conformance tests specified in this document do not include the assessment of performance nor robustness or reliability of an implementation. They cannot provide judgments on the physical realization of abstract service primitives, how a system is implemented, how it provides any requested service, nor the environment of the protocol implementation. Furthermore, the abstract test cases defined in this document only consider the communication protocol and the system's behaviour defined ISO 15118-8. The power flow between the EVSE and the EV is not considered. NOTE - Practical limitations make it impossible to define an exhaustive test suite, and economic considerations can restrict testing even further. Hence, the purpose of this document is to increase the probability that different implementations are able to interwork. This is achieved by verifying them by means of a protocol test suite, thereby increasing the confidence that each implementation conforms to the protocol specification. However, the specified protocol test suite cannot guarantee conformance to the specification since it detects errors rather than their absence. Thus, conformance to a test suite alone cannot guarantee interworking. Instead, it gives confidence that an implementation has the required capabilities and that its behaviour conforms consistently in representative instances of communication.

Obsah

ČSN CLC/TS 50600-5-1 Tento dokument představuje model zralosti řešící dopad prostředků, infrastruktur a zařízení informačních a komunikačních technologií (IKT) v datových centrech na životní prostředí (management s energií a udržitelnost životního prostředí).

Obsah

ČSN EN ISO 13703-3 This document provides a set of common supplementary requirements for the most frequently used materials in upstream oil and gas piping systems. This document is applicable to offshore and onshore production facilities, processing and gas liquefaction plants. The materials covered in this document are intended to be used in the following piping systems services: - category D, category M, normal and high pressure, according to ASME B31.3; - sour environments as defined in the ISO 15156 series. NOTE - For the purposes of this document, ANSI/NACE MR0175 is equivalent to the ISO 15156 series, and ANSI/NACE MR0103 is equivalent to ISO 17945. This document does not provide guidelines for material selection. The selection of suitable materials for a specific service including any necessary additional material requirements remains the responsibility of the end user. This document does not cover requirements related to: - sulfide stress cracking (SSC) in corrosive petroleum refining environments included in ISO 17945; - non-metallic piping systems according to ASME B31.3 or the ISO 14692 series; - marine piping systems, e.g. ballasting piping system, covered by classification rules; - subsea production systems; - downhole equipment; - transportation pipeline systems, including flowlines, designed in accordance with a recognized pipeline design code. Common requirements related to manufacture, inspection and procurement of piping and valve parts are included in Annex A and Annex B, providing material datasheets and element datasheets, respectively. These material and element datasheets can be applied for applications other than piping systems, e.g. pressure vessels and pumps based upon assessment of the end user and conformance with the selected design code for the relevant equipment. This document is not intended to limit the use of alternative materials or grades within a referenced material standard. Where the use of alternative materials/grades are considered appropriate, the end user is responsible for specifying any additional requirements necessary to meet the design code or specification.

Obsah

ČSN EN ISO 12736-3 This document specifies requirements for project specific product and process qualification of field applied wet thermal insulation systems applied at interfaces (e.g. field joints) and pre-fabricated insulation in the petroleum and natural gas industries. This document is applicable to wet thermal insulation systems submerged in seawater. This document is not applicable to: - the project qualification of anticorrosion coatings or the requirements for application thereof; - thermal insulation in the annulus of a steel pipe-in-pipe system.

Obsah

ČSN EN ISO 12736-2 This document specifies requirements for project specific product and process qualification of wet thermal insulation systems applied to pipelines in a factory setting and subsea equipment in the oil and gas industries. This document is not applicable to: - pre-fabricated insulation; - thermal insulation in the annulus of a steel pipe-in-pipe system; - maintenance works on existing installed wet thermal insulation systems; - project qualification of anticorrosion coatings or the requirements for application thereof.

Obsah

ČSN EN ISO 12736-1 This document provides a set of common supplementary requirements for the most frequently used materials in upstream oil and gas piping systems. This document is applicable to offshore and onshore production facilities, processing and gas liquefaction plants. The materials covered in this document are intended to be used in the following piping systems services: - category D, category M, normal and high pressure, according to ASME B31.3; - sour environments as defined in the ISO 15156 series. NOTE - For the purposes of this document, ANSI/NACE MR0175 is equivalent to the ISO 15156 series, and ANSI/NACE MR0103 is equivalent to ISO 17945. This document does not provide guidelines for material selection. The selection of suitable materials for a specific service including any necessary additional material requirements remains the responsibility of the end user. This document does not cover requirements related to: - sulfide stress cracking (SSC) in corrosive petroleum refining environments included in ISO 17945; - non-metallic piping systems according to ASME B31.3 or the ISO 14692 series; - marine piping systems, e.g. ballasting piping system, covered by classification rules; - subsea production systems; - downhole equipment; - transportation pipeline systems, including flowlines, designed in accordance with a recognized pipeline design code. Common requirements related to manufacture, inspection and procurement of piping and valve parts are included in Annex A and Annex B, providing material datasheets and element datasheets, respectively. These material and element datasheets can be applied for applications other than piping systems, e.g. pressure vessels and pumps based upon assessment of the end user and conformance with the selected design code for the relevant equipment. This document is not intended to limit the use of alternative materials or grades within a referenced material standard. Where the use of alternative materials/grades are considered appropriate, the end user is responsible for specifying any additional requirements necessary to meet the design code or specification.

Obsah

ČSN EN 13369 This document provides the specifications, the basic performance criteria and the Assessment and Verification of Constancy of Performance (AVCP) for unreinforced, reinforced and prestressed precast concrete products made of compact light-, normal- and heavyweight concrete according to EN 206 with no appreciable amount of entrapped air other than entrained air. Concrete containing fibres for other than mechanical properties (steel, polymer or other fibres) is also covered. It does not cover precast reinforced components of lightweight aggregate concrete with open structure nor glass-fibre reinforced concrete. It can also be used to specify products for which there is no standard. Not all of the specifications (Clause 4) of this document are relevant to all precast concrete products. Some European product standards refer to this document. They can include specific provisions that take precedence over the provisions of this document.

Obsah

ČSN EN 16637-2 This document specifies a dynamic surface leaching test (DSLT) which is aimed at determining the release per unit surface area as a function of time of inorganic and/or non-volatile organic substances from a monolithic, plate- or sheet-like product, when it is put into contact with an aqueous solution (leachant). The test method is not suitable for substances that are volatile under ambient conditions. This test is a parameter specific test focusing on identifying and specifying parameter specific properties tested under specified conditions. It is not aimed at simulating real situations. The application of results to specific intended conditions of use can be established by means of modelling (not included in this document). The test method applies to more or less regularly shaped test portions consisting of monolithic test pieces with minimum dimensions of 40 mm in all directions [volume > 64 000 mm3 (64 cm3)]. It also applies to plate- or sheet-like products with surface areas of minimum 10 000 mm2 (100 cm2) exposed to the leachant. Products designed to drain water (e.g. draining tiles, porous asphalt) and monolithic granular products according to EN 16637-1:2023, Table 1, are also tested by this test method. All products to be tested are assumed to maintain their integrity over a time frame relevant for the considered intended use. The modification for granular construction products with low hydraulic conductivity (Annex A) applies for granular particles with so little drainage capacity between the grains that percolation in percolation tests and in practice is nearly impossible. Metals, metallic coatings and organic coatings on metals are excluded from the scope of this document because the principles of this test (diffusion) are not obeyed by these products. Guidance on the need for testing of these products is under consideration. For some coatings (e.g. some renders with organic binders according to EN 15824 [9]) in intermittent contact with water, physical and chemical properties might be changed in permanent contact with water. For these products, this document is not appropriate. Guidance on the applicability of the test method to a given product is outlined in EN 16637-1.

Obsah

ČSN EN 16637-3 This document specifies an up-flow percolation test (PT) which is applicable to determine the leaching behaviour of inorganic and non-volatile organic substances from granular construction products. The test is not suitable for substances that are volatile under ambient conditions. The construction products are subjected to percolation with water as a function of liquid to solid ratio under specified percolation conditions. The method is a once-through column leaching test. This up-flow percolation test is performed under specified test conditions for construction products and does not necessarily produce results that mimic specific intended use conditions. This test method produces eluates, which can subsequently be characterized by physical, chemical and ecotoxicological methods according to existing standard methods. The results of eluate analysis are presented as a function of the liquid/solid ratio. The test results enable the distinction between different leaching behaviour. In this document the same test conditions as for EN 17516 (CEN/TC 444/WG 1) are applied in order to allow full comparability of testing construction products and waste derived construction products to avoid double testing. The EN 17516 test results are eligible in the context of testing construction products as well.

Obsah

ČSN EN ISO 52016-3 (73 0336) This document specifies procedures for the calculation of the energy needs for heating and cooling, internal temperatures and sensible and latent heat loads of a building according to the hourly calculation methodology in ISO 52016-1. Additions or modifications of the calculations are provided in this document if the building envelope contains one or more adaptive building envelope elements (building envelope elements with adaptive components that are either environmentally or actively controlled as a function of specific conditions). The adaptive building envelope element replaces the transparent building element in the calculation according to ISO 52016-1. The three types of adaptive building envelope elements covered in this document are: - building envelope elements with dynamic solar shading; - building envelope elements with chromogenic glazing; - building envelope elements with an actively ventilated cavity. Environmentally activated control is described for building envelope elements with chromogenic glazing, but can also occur for other types of adaptive building envelope elements. In that case the same approach applies as for environmentally activated chromogenic glazing. This document is applicable to the assessment of the energy performance of buildings (EPB) (energy performance labels and certificates), including comparison between buildings and checking conformity with minimum energy performance criteria. It is also applicable to assess the contribution of the adaptive building envelope element to the smart readiness of a building. In addition, this document provides indicators for the impact of the adaptive building envelope element on the performance of the building compared to a reference building envelope element. It is applicable to buildings at the design stage, to new buildings after construction and to existing buildings in the use phase. This document is not applicable to geometrically complex adaptive building envelope elements that can only be modelled as multiple coupled thermal zones. NOTE - The background to the selection of adaptive building envelope elements is given in ISO/TR 52016-4.

Obsah

ČSN EN 14350+A1 Tento dokument specifikuje bezpečnostní požadavky týkající se materiálů, konstrukce, provedení, balení a informací o výrobcích pro vybavení pro pití určená pro děti ve věku od 0 do 48 měsíců (viz B.2): - opakovaně použitelné nádoby a opakovaně použitelné pomůcky pro pití; - nádoby na jedno použití a pomůcky pro pití prodávané s těmito nádobami; - sosáky na jedno použití; - sosáky k okamžitému použití. Tento dokument nezahrnuje požadavky na čistotu výrobků připravených k použití a výrobků na jedno použití. Tento dokument se nevztahuje na výrobky určené pro speciální klinické lékařské aplikace, např. ty, které se týkají rozštěpů patra. Tento dokument se nevztahuje na vybavení pro pití vyrobená z keramiky. Tento dokument se nevztahuje na sáčky určené pouze pro skladování. Tento dokument se nevztahuje na vybavení pro pití, která při nákupu obsahují tekutiny nebo potraviny, a vybavení pro krmení je k nim připevněné. Tento dokument se nevztahuje na šidítka. Bezpečnostní požadavky a zkušební metody pro šidítka jsou stanoveny v EN 1400 [6]. Tento dokument se nevztahuje na příbory a jiné nádobí na krmení. Bezpečnostní požadavky a zkušební metody pro příbory a nádobí pro krmení jsou stanoveny v EN 14372 [7]. U vybavení pro pití vyloučených z předmětu této normy se zvažují vždy možné požadavky tohoto dokumentu, kdykoli je to možné.