Normy

Obsah

ČSN EN IEC 62056-6-1 ed. 4 This part of IEC 62056 specifies the overall structure of the OBject Identification System (OBIS) and the mapping of all commonly used data items in metering equipment to their identification codes. OBIS provides a unique identifier for all data within the metering equipment, including not only measurement values, but also abstract values used for configuration or obtaining information about the behaviour of the metering equipment. The ID codes defined in this document are used for the identification of: - logical names of the various instances of the ICs, or objects, as defined in IEC 62056-6-2:2023; - data transmitted through communication lines; - data displayed on the metering equipment, see Clause A.2 in Annex A. This document applies to all types of metering equipment, such as fully integrated meters, modular meters, tariff attachments, data concentrators, etc. To cover metering equipment measuring energy types other than electricity, combined metering equipment measuring more than one type of energy or metering equipment with several physical measurement channels, the concepts of medium and channels are introduced. This allows meter data originating from different sources to be identified. While this document fully defines the structure of the identification system for other media, the mapping of non-electrical energy related data items to ID codes is completed separately. NOTE - EN 13757-1:2014 defines identifiers for metering equipment other than electricity: heat cost allocators, thermal energy, gas, cold water and hot water.

Obsah

ČSN EN 16272-6 This document describes a test method for measuring a quantity representative of the intrinsic characteristics of airborne sound insulation for rail noise barriers and related devices: the sound insulation index. The test method is intended for the following applications: - determination of the intrinsic characteristics of airborne sound insulation of noise barriers and related devices to be installed along railways, to be measured either on typical installations alongside railways or in laboratory conditions; - determination of the intrinsic characteristics of airborne sound insulation of noise barriers and related devices in actual use; - comparison of design specifications with actual performance data after the completion of the construction work; - verification of the long-term performance of noise barriers and related devices (with a repeated application of the method); - interactive design process of new products, including the formulation of installation manuals. The test method is not intended for the determination of the intrinsic characteristics of airborne sound insulation of noise barriers and related devices to be installed in reverberant conditions, e.g. inside tunnels or deep trenches or under covers. Results are expressed as a function of frequency in one-third octave bands, where possible, between 100 Hz and 5 kHz. If it is not possible to get valid measurement results over the whole frequency range indicated, the results need to be given in a restricted frequency range and the reasons for the restriction(s) need to be clearly reported.

Obsah

ČSN EN 12255-6 Tento dokument specifikuje funkční požadavky na čištění odpadních vod při využití aktivačního procesu v čistírnách odpadních vod pro více než 50 ekvivalentních obyvatel. Informativní přílohy A až W poskytují informace pro navrhování.

Obsah

ČSN EN ISO 10555-1 This document specifies general requirements for intravascular catheters, supplied sterile and intended for single use, for any application. This document does not apply to intravascular catheter accessories, e.g. those covered by ISO 11070.

Obsah

ČSN EN 17795-5 This code of practice provides a set of guidelines for lifting and motion operations related to machinery and machinery installations used in staging and production facilities for events. This document is pertinent to all the machinery phases, assembly, commissioning, setting, operation and dismantling employed in the event industry including machinery defined in point j, Article 1.2 of the Machinery Directive (2006/42/EC): "machinery intended to move performers during artistic performances". This document also applies to machinery and machinery installations based on new technologies or specially designed installations which are not expressly mentioned here but which nevertheless operate in a similar manner or are meant for similar purposes to those listed above. This document does not provide specific details but is intended to provide general guidelines on planning and the process of lifting and motion operations.

Obsah

ČSN EN 15091 The purpose of this document is to specify requirements for marking, identification, leaktightness, electrical and operational safety and mechanical resistance for sanitary tapware with opening and closing controlled electronically.

Obsah

ČSN EN 1755 This document is applicable to self-propelled and pedestrian propelled manual and semi-manual industrial trucks as defined in ISO 5053 1:2020 including their load handling devices and attachments (hereafter referred to as trucks) intended for use in potentially explosive atmospheres. NOTE 1 - Attachments mounted on the load carrier or on fork arms which are removable by the user are not considered to be a part of the truck. This document specifies supplementary technical requirements for the prevention of the ignition of an explosive atmosphere of flammable gases, vapours, mists or dusts by industrial trucks of equipment group II and equipment category 2G, 3G, 2D or 3D. NOTE 2 - The relationship between an equipment category (hereafter referred to as category) and the corresponding zone (area classification) is shown in informative Annex B. This document does not apply to: - trucks of equipment group I; - trucks of equipment group II, equipment category 1; - trucks intended for use in potentially explosive atmospheres with hybrid mixtures; - protective systems. This document does not apply to trucks intended for use in potentially explosive atmospheres of carbon disulfide (CS2), carbon monoxide (CO) and/or ethylene oxide (C2H4O) due to the special properties of these gases. Technical requirements relating to lithium-ion batteries and fuel cells as energy sources are not given in this document due to their specific hazards.

Obsah

ČSN EN IEC 62271-207 ed. 3 Tato část IEC 62271 platí pro: - plynem izolované rozváděče (GIS) - kovově kryté rozváděče střídavého proudu na jmenovitá napětí nad 1 kV do 52 kV včetně podle IEC 62271-200 umístěné na zemi nebo na podlaze určené pro použití v seizmických podmínkách a - izolačně kryté rozváděče střídavého proudu na jmenovitá napětí nad 1 kV do 52 kV včetně podle IEC 62271-201 umístěné na zemi nebo na podlaze určené pro použití v seizmických podmínkách. Hodnocení seizmické odolnosti rozváděčů zahrnuje zkoušky typických rozváděčů v kombinaci s analytickými metodami. Bere se v úvahu vzájemné působení mezi přímo namontovaným pomocným a řídicím zařízením a rozváděčem. Filozofie hodnocení seizmické odolnosti zahrnuje volbu hladiny seizmické odolnosti (kapitola 4), metodologii hodnocení zkouškami (kapitola 5), hodnocení kombinací zkoušky a numerické analýzy (kapitola 6), kritéria pro vyhodnocení seizmické zkoušky (kapitola 7) a dokumentaci pro hodnocení seizmické zkoušky (kapitola 8). Kritéria pro posuzování vhodnosti rozváděčů jsou uvedena v příloze B. Vývojový diagram procesu hodnocení seizmické odolnosti je uveden v příloze C. Seizmické hodnocení rozváděčů je prováděno výrobcem obvykle na základě požadavku.

Obsah

ČSN EN 1991-1-3 ed. 2 přejímá evropskou normu EN 1991-1-3:2003, včetně jejích změn a oprav a tvoří její konsolidované znění. Norma obsahuje text normy ČSN EN 1991-1-3 (73 0035) z června 2005 a zapracovanou opravu ČSN EN 1991-1-3:2005/Opr. 1 z února 2010, změnu ČSN EN 1991-1-3:2005/Z1 z října 2006, změnu ČSN EN 1991-1-3:2005/Z2 z února 2010, změnu ČSN EN 1991-1-3:2005/Z3 z března 2010, změnu ČSN EN 1991-1-3:2005/Z4 z dubna 2012, změnu ČSN EN 1991-1-3:2005/Z5 z června 2013, změnu ČSN EN 1991-1- 3:2003/A1:2015, změnu Z6 z ledna 2022 a změnu Z7 z července 2024.

Obsah

ČSN EN ISO 13141 This document establishes requirements for short-range communication for the purposes of augmenting the localization in autonomous electronic fee collection (EFC) systems. Localization augmentation serves to inform on-board equipment (OBE) about geographical location and the identification of a charge object. This document specifies the provision of location and heading information and security means to protect against the manipulation of the OBE with false RSE. The localization augmentation communication (LAC) takes place between an OBE in a vehicle and fixed RSE. This document is applicable to OBE in an autonomous mode of operation. This document specifies attributes and functions for the purpose of localization augmentation, by making use of the dedicated short-range communications (DSRC) communication services provided by DSRC Layer 7, and makes these LAC attributes and functions available to the LAC applications at the RSE and the OBE. Attributes and functions are specified on the level of application data units (ADUs; see Figure 1). As depicted in Figure 1, this document is applicable to: - the application interface definition between OBE and RSE; - the interface to the DSRC application layer, as specified in ISO 15628 and EN 12834; - the use of the DSRC stack. The LAC is suitable for a range of short-range communication media. This document provides specific definitions regarding the CEN-DSRC stack as specified in EN 15509. Annexes C, D, E and H provide for the use of the Italian DSRC as specified in ETSI/ES 200 674-1,[9] ISO CALM IR,[3] ARIB DSRC[10] and WAVE DSRC.[11] This document contains a protocol implementation conformance statement (PICS) proforma in Annex B and transaction examples in Annex F. Annex G highlights how to use this document for the European Electronic Toll Service (EETS). Test specifications are not within the scope of this document.

Obsah

ČSN EN 3645-002 This document specifies the performances and contact arrangements for threaded ring coupling circular connectors, fire resistant or non-fire resistant, intended for use in a temperature range from -65 °C to 175 °C or 200 °C continuous.

Obsah

ČSN EN IEC 60034-27-2 Norma pojednává o online měřeních PD a poskytuje společný základ pro normalizované postupy pro měřicí techniky a přístroje, uspořádání instalace, normalizaci a posuzovaní citlivosti, měřicí postupy, snížení šumu, dokumentaci a interpretaci výsledků. Dokument se týká online měření částečných výbojů na izolaci statorového vinutí točivých elektrických strojů se jmenovitým napětím 3 kV a vyšším, které nejsou poháněny z měniče. Zahrnuje měřicí systémy PD a metody pro detekování elektrických signálů PD. Stejná měřicí zařízení a stejné postupy lze také použít pro detekci elektrického jiskření a pro detekci jevu hoření oblouku.