Normy

Obsah

ČSN EN 17860-3 This document is applicable to multi track carrier cycles with or without electric assistance and a maximum gross vehicle weight of 300 kg. NOTE1 - Requirements that are similar to single track carrier cycles are covered in Part 2 of this standard series. NOTE2 - Requirements for electrical power assisted carrier cycles will be covered in Part 5 of this standard series.

Obsah

ČSN EN 4888 This document specifies minimum reliability test requirements for sub-components of commercial aircraft passenger seats. Test procedures including in-service load cases regarding passenger behaviour for sub-seat components are specified. Abuse loads are excluded. This document is applicable to the sub-seat components such as but not limited to backrest, headrest, armrest, table, literature pocket and control elements. This document does not apply to belts, Inflight-Entertainment, seat dress cover and cushions. Additional environmental influences like temperature, radiation, gases and liquids may also alter the reliability of the aircraft passenger seats and their sub-components over their lifetime but are not taken into consideration in this document. Tests on abrasion and surface durability are specified in EN 4860, EN 4864 and EN 4876.

Obsah

ČSN ETSI EN 302 064 V2.2.1 The present document applies to terrestrial wireless digital video link equipment operating in the frequency band 1,3 GHz to 50 GHz. The present document does not apply to transmitter equipment where the output power exceeds 10 W. Equipment with an integral antenna is also excluded. NOTE - The relationship between the present document and essential requirements of article 3.2 of Directive 2014/53/EU [i.1] is given in annex A.

Obsah

ČSN ETSI EN 303 798 V2.1.1 Tento dokument definuje fyzickou vrstvu, linkovou vrstvu a konfiguraci rádiových zdrojů seskupených do přístupové vrstvy stanice ITS podle referenční architektury v ETSI TS 103 898 [i.2]. Technologie přístupové vrstvy, která je specifikována v tomto dokumentu, se vztahuje na takzvaný sidelink nebo také PC5 rozhraní buňkové V2X pro následující kmitočtová pásma: - provoz v kmitočtovém pásmu vyhrazeném pro aplikace ITS související s bezpečností v kmitočtovém rozsahu 5,875 GHz až 5,925 GHz; - provoz v kmitočtových pásmech vyhrazených pro aplikace ITS nesouvisející s bezpečností v kmitočtovém rozsahu 5,855 GHz až 5,875 GHz. Tento dokument je revizí ETSI EN 303 613 [i.1] a rozšiřuje specifikaci přístupové vrstvy LTE-V2X tak, aby zahrnovala NR-V2X. To, zda se pro přenos zpráv v kanálu ITS používá LTE-V2X nebo NR-V2X, je určeno konfigurací na úrovni systému a je mimo rozsah platnosti tohoto dokumentu.

Obsah

ČSN EN 16867+A2 Tento dokument se aplikuje na mechatronické dveřní kování (MDF) vhodné pro dveřní sestavy, které umožňují řízené zamykání a/nebo uvolňování částí prostřednictvím oprávněných elektronických prostředků. To může být účinné pověřeními (např. karta, kód, biometricky apod.). MDF podle tohoto dokumentu je kombinována se zámky podle EN 12209, EN 14846, EN 15685 nebo může být částí nouzových dveřních uzávěrů podle EN 179, EN 1125 nebo EN 13637. MDF může být samostatné nebo spojené s vnějším řídicím systémem. Dokument by měl povolit klasifikaci MDF v několika charakteristikách jako je kategorie použití, životnost, okolní prostředí, bezpečnost a typ ovládacího zařízení. Vhodnost MDF pro použití na požárně odolných nebo protikouřových dveřních sestavách je určena zkouškami požární odolnosti provedenými navíc ke zkoušení vlastností určenými tímto dokumentem. Tento dokument nezahrnuje: - mechatronické cylindrické vložky podle EN 15684; - elektromechanicky ovládané zámky a zapadací plechy podle EN 14846.

Obsah

ČSN EN IEC 62381 ed. 3 This International Standard defines requirements and checklists for the factory acceptance test (FAT), the factory integration test (FIT), the site acceptance test (SAT), and the site integration test (SIT). These tests are carried out to demonstrate that the automation system meets the requirements of the applicable specification. This document provides a means for all parties, including the owner, the buyer, and the vendor, to clearly establish and agree on the scope of activities and responsibilities involved in performing these tests in order to achieve a timely delivery and acceptance of the automation system. The activities specified in this document can be used to develop test plans adapted to the specific requirements of the process/plant/equipment. The annexes of this document contain checklists which are available for consideration when preparing specific test procedures and documentation for a specific automation system.

Obsah

ČSN EN IEC 60384-9 ed. 3 This part of IEC 60384 is applicable to fixed capacitors of ceramic dielectric with a defined temperature coefficient (dielectric Class 2), intended for use in electronic equipment, including leadless capacitors but excluding fixed surface mount multilayer capacitors of ceramic dielectric, which are covered by IEC 60384-22 (Class 2). Capacitors for electromagnetic interference suppression are not included, but are covered by IEC 60384-14. The object of this document is to specify preferred ratings and characteristics and to select from IEC 60384-1:2021 the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of capacitor. Test severities and requirements specified in detail specifications referring to this document provide specific test severities and requirements of an equal or higher performance level. Further information on the conception of generic, sectional and detail specifications can be found in the Introduction of IEC 60384-1:2021.

Obsah

ČSN EN IEC 62933-1 ed. 2 Tato část IEC 62933 definuje termíny platící pro akumulaci elektrické energie (EES) včetně termínů nezbytných pro stanovení parametrů zařízení, zkušebních postupů, plánování, instalace, bezpečnostní problematiky a problematiky týkajících se okolního prostředí. Tento terminologický dokument platí pro systémy připojené k síti, které mohou odebírat elektrickou energii z napájecí elektrické soustavy, vnitřně ji ukládat a dodávat elektrickou energii do napájecí elektrické soustavy. Nabíjení a vybíjení systému EES může zahrnovat přeměnu energie.

Obsah

ČSN EN ISO 22476-16 (72 1004) This document is applicable to the borehole shear test using the phicometer procedure, commonly named the phicometer test (etymologically derived from phi for friction angle, co for cohesion and meter for measurement). The test can be performed in all types of natural soils, fills and artificial soils, which can be saturated or not. It does not apply to very soft fine soils, very loose coarse soils, medium strong to very strong rocks and natural or artificial soils with a predominance of cobbles having a particle diameter greater than 150 mm. Generally, the test is applicable in soils with an order of magnitude of their in situ resistance characteristics as follows: - Ménard pressuremeter limit pressure: 0,4 MPa < plM < 3,5 MPa approximately or more than 4 MPa in granular non-cohesive soils; - CPT Cone resistance: 1,5 MPa

Obsah

ČSN 76 1110 Tato norma obsahuje klasifikační tabulku, která slouží jako pomůcka pro zařazování ubytovacích zařízení kategorií hotel, hotel garni, penzion, motel, apartmánový hotel a apartmánový komplex do příslušných tříd podle minimálních stanovených požadavků na vybavenost a rozsah poskytovaných služeb.

Obsah

ČSN EN IEC 60512-28-100 ed. 3 This part of IEC 60512 specifies the test methods for signal integrity and transmission performance for connectors specified in respective parts of IEC 60603-7 [1], IEC 61076-1 [2], IEC 61076-2 [3], IEC 61076-3 [4] and IEC 63171 [5] series of standards for connecting hardware applications from 0,1 MHz up to 2 000 MHz, with reference to this document. NOTE - This document is also suitable for testing signal integrity and transmission performance of connectors up to a lower value of maximum frequency; however, the test methodology specified in the detail specification for any given connector remains the reference conformance test for that connector. The list of connector series of standards does not preclude referencing this document in other connector manufacturer's specifications or published standards. Test procedures provided herein are: - insertion loss, test 28a; - return loss, test 28b; - near-end crosstalk (NEXT) test 28c; - far-end crosstalk (FEXT), test 28d; - transverse conversion loss (TCL), test 28f; - transverse conversion transfer loss (TCTL), test 28g. Other test procedures referenced herein are: - shield transfer impedance (ZT), see IEC 60512-26-100, test 26e. - coupling attenuation (aC), see IEC 62153-4-7 and IEC 62153-4-12. - low frequency coupling attenuation (aCLF) see IEC 62153-4-7 and IEC 62153-4-15.

Obsah

ČSN EN 12464-2 (36 0450) This document specifies lighting requirements for humans in outdoor work places, which meet the needs for visual comfort and performance of people having normal, or corrected to normal ophthalmic (visual) capacity. Usual visual tasks and the avoidance of obtrusive light are considered. This document specifies requirements for lighting solutions for most outdoor work places and their associated areas in terms of quantity and quality of illumination. In addition, recommendations are given for good lighting practice. This document does not specify lighting requirements with respect to the safety and health of people at work and has not been prepared in the field of application of Article 153 of Treaty on the Functioning of the European Union although the lighting requirements, as specified in this document, usually fulfil safety needs. NOTE - Lighting requirements with respect to the safety and health of workers at work can be contained in Directives based on Article 153 of Treaty on the Functioning of the European Union, in national legislation of member states implementing these directives or in other national legislation of member states. This document neither provides specific solutions, nor restricts the designers' freedom from exploring new techniques nor restricts the use of innovative equipment. The illumination can be provided by daylight, electric lighting or a combination of both. This document is not applicable for the lighting of indoor work places and underground mining or emergency lighting. For indoor work places, see EN 12464-1 and for emergency lighting, see EN 1838 and EN 13032-3.