Normy

Obsah

ČSN EN 1538+A1 Tato evropská norma ustanovuje obecné zásady pro provádění podzemních stěn a to jak pažicích tak i těsnicích. POZNÁMKA 1: Tato norma se týká pouze stavebních konstrukcí zhotovených v rýze, vytěžené s podporou suspenze nebo za suchých podmínek, kde zemina je odstraněna a nahrazena betonem nebo samotvrdnoucí suspenzí a s tloušťkou stěny B 40 cm. POZNÁMKA 2: Podzemní stěny mohou být trvalými nebo dočasnými stavebními konstrukcemi. POZNÁMKA 3: Pojednány jsou následující typy stavebních konstrukcí: a) Pažicí stěny: obvykle se zřizují k zapažení bočních stěn výkopů v základové půdě. Zahrnují: 1) monolitické betonové podzemní stěny; 2) prefabrikované betonové podzemní stěny; 3) podzemní stěny z vyztužené samotvrdnoucí suspenze. b) Těsnicí podzemní stěny: obvykle se zřizují k zamezení pohybu čisté nebo znečistěné podzemní vody nebo jiných kontaminantů v podloží. Zahrnují: 1) podzemní stěny ze samotvrdnoucí suspenze (případně s těsnicími fóliemi nebo se štětovnicemi); 2) podzemní stěny z plastického betonu. POZNÁMKA 4: Stěny vytvořené z mělkých vertikálních rýh (typicky výkopy s poměrem hloubky k tloušťce D/B 5 nebo D 5 m) nespadají pod tuto normu.

Obsah

ČSN ETSI EN 303 146-2 V1.2.1 Tento dokument definuje informační model a protokol pro rekonfigurovatelné vysokofrekvenční rozhraní pro rekonfigurovatelná mobilní zařízení (MD). Je založen na praktických případech definovaných v ETSI TR 102 944, na systémových požadavcích definovaných v ETSI EN 302 969 a na architektuře pro mobilní zařízení související s rádiovou rekonfigurací definované v ETSI EN 303 095.

Obsah

ČSN ETSI EN 300 433 V2.1.1 The present document covers the technical requirements for transmitters and receivers used in stations of angle modulated, Double Side Band (DSB) modulated and/or Single Side Band (SSB) modulated Citizens' Band (CB) radio equipment operating in all or part of the frequency band 26,960 MHz to 27,410 MHz with a channel spacing of 10 kHz, and intended for analogue speech and/or data transmission. Citizens' Band radio equipment operation is in accordance with ECC Decision (11)03 on the harmonised use of frequencies for Citizens' Band (CB) radio equipment [i.2]. Any equipment using national regulations on Citizens' Band (CB) permitting the use of channels outside of the carrier frequencies shown in table 1 within the frequency range from 26 MHz to 28 MHz can use the present document. The types of equipment covered by the present document are as follows: - Base station: equipment fitted with antenna connector. - Mobile station: equipment fitted with antenna connector. - Hand portable stations: a) either fitted with an antenna connector; or b) without an external antenna connector but fitted with a permanent internal or a temporary internal 50 ohm RF connector which allows access to the transmitter output and the receiver input. Hand portable station equipment without an external or internal Radio Frequency (RF) connector and without the possibility of having a temporary internal 50 ohm RF connector is not covered by the present document (integral antenna equipment). The present document contains requirements to demonstrate that "... Radio equipment shall be so constructed that it both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference" and that "....radio equipment supports certain features ensuring access to emergency services". In addition to the present document, other ENs that specify technical requirements in respect of essential re-quirements under other parts of article 3 of the Radio Equipment Directive [i.4] may apply to equipment within the scope of the present document.

Obsah

ČSN ETSI EN 301 908-21 V6.1.1 The present document applies to the following radio equipment type: " Mobile WiMAXTM FDD User Equipment for IMTOFDMA TDD WMAN. The present document contains requirements to demonstrate that Radio equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference. In addition to the present document, other ENs that specify technical requirements in respect of essential re-quirements under other parts of article 3 of the Radio Equipment Directive 2014/53/EU [i.2] may apply to equip-ment within the scope of the present document. NOTE: A list of such ENs is included on the web site http://www.newapproach.org.

Obsah

ČSN ETSI EN 301 908-20 V6.3.1 The present document applies to the following radio equipment type: " Base stations for IMT-2000 OFDMA TDD WMAN (Mobile WiMAXTM) operating in TDD mode. The requirements in the present document apply to both Wide Area Base Stations and Local Area Base Stations unless otherwise stated. The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference. In addition to the present document, other ENs that specify technical requirements in respect of essential re-quirements under other parts of article 3 of the Radio Equipment Directive 2014/53/EU [i.2] may apply to equip-ment within the scope of the present document. NOTE: A list of such ENs is included on the web site http://www.newapproach.org.

Obsah

ČSN ETSI EN 301 908-19 V6.3.1 The present document applies to the following radio equipment type: User Equipment for IMT-2000 OFDMA TDD WMAN (Mobile WiMAXTM) operating in TDD mode. The present document contains requirements to demonstrate that Radio equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference. In addition to the present document, other ENs that specify technical requirements in respect of essential re-quirements under other parts of article 3 of the Radio Equipment Directive 2014/53/EU [i.2] may apply to equip-ment within the scope of the present document. NOTE: A list of such ENs is included on the web site http://www.newapproach.org.

Obsah

ČSN ETSI EN 303 098 V2.1.1 The present document lays down the minimum requirements for low power maritime personal locating devices employing AIS The present document does not cover requirements for the integrated GNSS receiver providing locating function. The present document incorporates the relevant provisions of the International Telecommunication Union (ITU) radio regulations [i.4] included in Recommendation ITU R M.1371-5 [1]. For this application, both the radiated power and the length of time of operation are limited to enable the equipment to be sufficiently small and light to be worn comfortably at all times and to limit the operating range to a local area. The present document also specifies technical characteristics, methods of measurement and required test results. The present document contains requirements to demonstrate that "... Radio equipment shall be so constructed that it both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference" [i.1].

Obsah

ČSN ETSI EN 301 442 V2.1.1 The present document applies to Mobile Earth Station (MES) radio equipment which have the following charac-teristics: " these MES operate in a non-geostationary orbit (NGSO) mobile-satellite system; " these MES have both transmit and receive capabilities and operate in a Satellite-Personal Communica-tions Network (S-PCN). An S-PCN MES may be handheld, portable, vehicle-mounted, host connected, semi-fixed or fixed equipment, or may be an element in a multi-mode terminal. It may consist of a number of modules with associated connections and user interface, or may be a self-contained single unit; " these LMESs are controlled and monitored by a Network Control Facility (NCF). The NCF is outside the scope of the present document; " if the MES is an element in a multi-mode terminal, unless otherwise stated in the present document, its requirements apply only to the S-PCN MES element of the terminal operating in the MSS frequency bands given in table 1; The present document is intended to cover the provisions of Directive 2014/53/EU [7] (RE Directive) article 3.2 which states that "..radio equipment shall be so constructed that it both effectively uses and supports the effi-cient use of radio spectrum in order to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential re-quirements under other parts of article 3 of the Directive 2014/53/EU [7] may apply to equipment within the scope of the present document. NOTE: A list of such ENs is included on the ETSI web site.

Obsah

ČSN ETSI EN 301 430 V2.1.1 The present document applies to Satellite News Gathering (SNG) Transportable Earth Stations (TESs) which have the following characteristics: " the SNG TESs are designed for Satellite News Gathering (SNG) which can be either an unforeseen or pre-planned activity; " SNG TES is capable of transmitting television signals and associated audio or programme audio only towards a satellite positioned on the geostationary orbit. The modulation method may be either analogue or digital. Such transmissions are point-to-point or point-to-multipoint but not for general broadcast reception; " the SNG TESs are designed for relocation at any time to a different fixed operating location but are not intended to operate during the relocation period. The SNG TESs can be either vehicle mounted or packed for transportation. The SNG TESs considered in the present document are those designed to operate whilst stationary; " the SNG TESs are operating in the following bands allocated to the Fixed Satellite Services (FSS): - 10,70 GHz to 11,70 GHz (space-to-earth, shared); - 12,50 GHz to 12,75 GHz (space-to-earth, exclusive); - 12,75 GHz to 13,25 GHz (earth-to-space, shared); - 13,75 GHz to 14,25 GHz (earth-to-space, exclusive); - 14,25 GHz to 14,50 GHz (earth-to-space, shared). " frequencies could be selected from through the entire frequency range or be restricted to a range com-pletely enclosed within those bands. These bands are partly shared between FSS and Fixed Service (FS); " at present the ITU Radio Regulations [3] restrict the use of the 13,75 GHz to 14,00 GHz band to earth stations having an antenna diameter of 4,5 m or greater and having a transmitting EIRP between 68 dBW and 85 dBW; " the SNG TESs use linear polarization; " the SNG TESs operate through a geostationary satellite at least 3° away from any other geostationary satellite operating in the same frequency band and covering the same area; " the SNG TES antenna diameter does not exceed 5 m, or equivalent corresponding aperture; " the SNG TESs are designed for attended operation. The present document applies to the SNG TES with its ancillary equipment and its various terrestrial ports, and when operated within the boundary limits of the operational environmental profile declared by the applicant. The present document is intended to cover the provisions of Directive 2014/53/EU [6] (RE Directive) article 3.2, which states that ". radio equipment shall be so constructed that it both effectively uses and supports the effi-cient use of radio spectrum in order to avoid harmful interference." In addition to the present document, other ENs that specify technical requirements in respect of essential re-quirements under other parts of article 3 of the Directive 2014/53/EU [6]) may apply to equipment within the scope of the present document. NOTE: A list of such ENs is included on the ETSI web site.

Obsah

ČSN ETSI EN 301 721 V2.1.1 The present document applies to Mobile Earth Stations (MES) providing Low Bit Rate Data Communications (LBRDC) using Low Earth Orbiting (LEO) satellites and which have the following characteristics: - the MES could be a Based MES (BMES), a Vehicle mounted MES (VMES), or a Portable MES (PMES); - the MESs operate through satellites in Low Earth Orbit (LEO) as part of a network providing Low Bit Rate Data Communications (LBRDC);- The present document is intended to cover the provisions of Directive 2014/53/EU [7] (RE Directive) article 3.2 which states that "..radio equipment shall be so constructed that it both effectively uses and supports the effi-cient use of radio spectrum in order to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential re-quirements under other parts of article 3 of the RE Directive [7] may apply to equipment within the scope of the present document. NOTE 1: A list of such ENs is included on the ETSI web site. NOTE 2: The MESs are controlled and monitored by a Network Control Facility (NCF). The NCF is outside the scope of the present document.

Obsah

ČSN ETSI EN 302 574-3 V2.1.1 The present document applies to User Equipment (UE) radio equipment type which have the following charac-teristics: " these UEs have both transmit and receive capabilities and operate in a Geostationary satellite network; " these UEs operate with an assigned channel signal bandwidth (CBw) smaller than 1 MHz; " these UEs may be handset, handheld, portable, vehicle-mounted, host connected, semi-fixed or fixed equipment, or may be an element in a multi-mode terminal. It may consist of a number of modules with associated connections and user interface, or may be a self-contained single unit; " if the UE is an element in a multi-mode terminal, unless otherwise stated in the present document, its requirements apply only to the UE element of the terminal operating in the Mobile Satellite Service (MSS) frequency bands given in table 1. The present document is intended to cover the provisions of Directive 2014/53/EU [7] (RE Directive) article 3.2 which states that "..radio equipment shall be so constructed that it both effectively uses and supports the effi-cient use of radio spectrum in order to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential re-quirements under other parts of article 3 of the RE Directive [7] may apply to equipment within the scope of the present document. NOTE: A list of such ENs is included on the web site http://www.newapproach.org.

Obsah

ČSN ISO 21940-12 Tato část ISO 21940 uvádí typická uspořádání rotorů v pružném stavu podle jejich vlastností a požadavků na vyvážení, popisuje vyvažovací postupy, určuje metody posuzování konečného stavu vyvážení a uvádí vodítka pro kritéria jakosti vyvážení. Tato část ISO 21940 může také sloužit jako základ pro složitější zkoumání, např. když je nutné přesnější určení požadované jakosti vyvážení. Jestliže se patřičně respektují stanovené výrobní metody a tolerance vyvážení, lze očekávat uspokojivé provozní podmínky. Tato část ISO 21940 není určena k tomu, aby sloužila jako přejímací specifikace pro jakýkoli rotor, ale spíše, aby dávala návod, jak se vyhnout hrubým omylům a zbytečně omezujícím požadavkům. Případy rezonancí konstrukcí a jejich úprav nejsou předmětem této části ISO 21940. Uváděné metody a kritéria jsou výsledkem zkušeností získaných z provozu běžných průmyslových strojů. Nemusí být přímo použitelné u speciálních zařízení nebo za zvláštních okolností. Proto se mohou vyskytnout případy, kdy se lze od této části ISO 21940 odchýlit.