Normy

Obsah

ČSN EN IEC 62109-3 (36 4651) Tato část 3 IEC 62109 pokrývá zvláštní bezpečnostní požadavky na elektronické prvky, které jsou mechanicky a/nebo elektricky začleněny do (PV) modulů nebo systémů. Mechanicky a/nebo elektricky začleněné znamená, že celá kombinace elektronického zařízení s fotovoltaickým prvkem se prodává jako jeden výrobek. Nicméně, zkoušky v této normě lze také použít k vyhodnocení kompatibility PV modulů a elektronických zaří-zení, které se prodávají samostatně a jsou určeny k instalaci blízko sebe. Položky zahrnuté v tomto rozsahu platnosti: Elektronická zařízení kombinovaná s PV moduly, která vykonávají funkce, jako jsou, ale bez omezení na, přeměnu výkonu DC-DC nebo DC-AC, aktivní diody, ochrany, ovládání, monitorování nebo komunikaci. Tyto požadavky se konkrétně týkají takovýchto elektronických zařízení používaných v kombinaci s plochými foto-voltaickými (PV) moduly.

Obsah

ČSN EN ISO 13304-2 The purpose of this document is to provide minimum criteria required for quality assurance and quality control, evaluation of the performance and to facilitate the comparison of measurements related to absorbed dose estimation obtained in different laboratories applying ex vivo X-band EPR spectroscopy with human tooth enamel. This document covers the determination of absorbed dose in tooth enamel (hydroxyapatite). It does not cover the calculation of dose to organs or to the body. This document addresses: a) responsibilities of the customer and laboratory; b) confidentiality and ethical considerations; c) laboratory safety requirements; d) the measurement apparatus; e) preparation of samples; f) measurement of samples and EPR signal evaluation; g) calibration of EPR dose response; h) dose uncertainty and performance test; i) quality assurance and control.

Obsah

ČSN EN ISO 13304-1 The primary purpose of this document is to provide minimum acceptable criteria required to establish a procedure for retrospective dosimetry by electron paramagnetic resonance spectroscopy and to report the results. The second purpose is to facilitate the comparison of measurements related to absorbed dose estimation obtained in different laboratories. This document covers the determination of absorbed dose in the measured material. It does not cover the calculation of dose to organs or to the body. It covers measurements in both biological and inanimate samples, and specifically: a) based on inanimate environmental materials like glass, plastics, clothing fabrics, saccharides, etc., usually made at X-band microwave frequencies (8 GHz to 12 GHz); b) in vitro tooth enamel using concentrated enamel in a sample tube, usually employing X-band frequency, but higher frequencies are also being considered; c) in vivo tooth dosimetry, currently using L-band (1 GHz to 2 GHz), but higher frequencies are also being considered; d) in vitro nail dosimetry using nail clippings measured principally at X-band, but higher frequencies are also being considered; e) in vivo nail dosimetry with the measurements made at X-band on the intact finger or toe; f) in vitro measurements of bone, usually employing X-band frequency, but higher frequencies are also being considered. For biological samples, in vitro measurements are carried out in samples after their removal from the person or animal and under laboratory conditions, whereas the measurements in vivo are carried out without sample removal and may take place under field conditions.

Obsah

ČSN EN 10025-4+A1 Tento dokument specifikuje technické dodací podmínky pro ploché a dlouhé výrobky ze za tepla válcované svařitelné jemnozrnné oceli v termomechanicky válcovaném stavu se značkami a jakostními stupni uvedenými v tabulkách 1 až 3 (chemické složení) a v tabulkách 4 až 6 (mechanické vlastnosti) v tloušťkách

Obsah

ČSN EN ISO 11681-2 Tento dokument stanovuje bezpečnostní požadavky a opatření pro jejich ověřování pro návrh, konstrukci, přepravu a uvádění do provozu přenosných ručních řetězových pil se spalovacím motorem určených pro vyvětvování stromů majících maximální hmotnost 4,3 kg (bez vodicí lišty nebo pilového řetězu a s prázdnými nádržemi). Řetězové pily jsou určeny pro používání s pravou rukou na zadní rukojeti a s levou rukou na přední rukojeti, zaškolenou osobou. Tento dokument se nevztahuje na vyřazování z provozu a sešrotování. Jsou specifikovány metody pro vyloučení nebo snížení nebezpečí vyplývajících z používání těchto strojů a typ informací o bezpečných pracovních postupech poskytnuté výrobce. Tento dokument se zabývá všemi významnými nebezpečími, nebezpečnými situacemi a nebezpečnými událostmi relevantních pro tyto stroje, pokud jsou používány, jak je určeno, a za podmínek nesprávného použití, které jsou důvodně předvídatelné výrobcem (viz příloha B). Tento dokument platí pro řetězové pily vyrobené po jeho datu vydání.

Obsah

ČSN EN ISO 11681-1 Tento dokument specifikuje bezpečnostní požadavky a opatření pro ověřování pro návrh, konstrukci, přepravu a uvedení do provozu přenosných ručních řetězových pil se spalovacím motorem. Řetězové pily jsou určeny pro lesnické práce pouze jednou obsluhou, s pravou rukou na zadní rukojeti a levou rukou na přední rukojeti. Tento dokument se nevztahuje na vyřazování z provozu a sešrotování výrobku. Jsou specifikovány metody pro vyloučení nebo snížení nebezpečí vyplývajících z používání těchto strojů a typ informací o bezpečných pracovních postupech poskytnuté výrobce. Tento dokument se zabývá všemi významnými nebezpečími, nebezpečnými situacemi a nebezpečnými událostmi, s výjimkou zpětného vrhu a vyvážení u strojů se zdvihovým objemem motoru větším než 80 cm3, relevantních pro tyto stroje, pokud jsou používány, jak je určeno, a za podmínek nesprávného použití. které jsou důvodně předvídatelné výrobcem (viz příloha A). Tento dokument platí pro řetězové pily vyrobené po jeho datu vydání.

Obsah

ČSN EN 16589-1 This document is applicable to articulated extraction arms used as a local exhaust device in laboratories and comprised of a specific capture device (receiving, enclosing or capture hood, nozzle or flat screen) connected to ducting to move air from the capture device to discharge. This document is a product standard. This document covers product performance type test methods. Occupational health and safety assessments methods are not included in this document. This document specifies: - a method to assess the three-dimensional capture zone of an articulated extract arms; - a method for assessing the isothermal and diffusive emission release capture efficiency of articulated extract arms and robustness to a challenge of air disturbance directly in front of and in close proximity to the capture hood and release source positioned on a table; - a method for establishing the reachable, three-dimensional workspace of articulated extract arms; - a method for measuring the pressure drop and noise level of articulated extract arms; - instructions for marking the devices and recommended information in the product manual; - guidance for use describing the limitations of articulated extract arms for different airflow rates; - guidance on selection, installation, commissioning, and testing of articulated extract arms and the associated local exhaust ventilation systems. The test procedure for capture efficiency and the guidance included in Annex A and B does not apply to particle sources or point sources which release contaminants with initial velocity of above 0,5 m/s due to temperature, pressure release, work process or similar. The scope does not include filtration requirements and impact of fully or partly recirculated airflow extracted by an articulated extract arm.

Obsah

ČSN ETSI EN 300 132-3 V2.3.1 The present document contains requirements and measurements methods for the physical interface "A3" that is situated between the power supply system(s) and the power consuming ICT equipment: - the nominal voltage at power interface "A3" of ICT equipment defined in the present document is DC voltage up to 400 V; - the output performance of the power equipment including the cable network at the interface "A3"; - the input of the ICT equipment connected to interface "A3". The DC power can be supplied by a DC output power system e.g. via on-grid AC rectifiers, from DC/DC converters in solar systems, fuel cells, standby generators including a battery backup. The present document aims at providing compatibility at interface "A3" between the power supply equipment and different ICT equipment (including/monitoring, cooling system, etc.) connected to the same power supply. The requirements are defined for the purpose of the present document to: - identify a power supply system with the same characteristics for all ICT equipment defined in the area of application; the area of application may be any location where the interface "A3" is used i.e. telecommunication centres, Radio Base Stations, datacentres and customer premises; - facilitate interworking of different loads; - facilitate the standardization of power supply systems for ICT equipment; - facilitate the installation, operation and maintenance in the same network of ICT equipment and systems from different origins; - secure robustness against temporary voltage deviations and transients during abnormal conditions. General requirements for safety and EMC are out of the scope of the present document series unless specific requirement not defined in existing safety or EMC standards.

Obsah

ČSN ETSI EN 301 908-1 V15.2.1 The present document applies to user equipment, repeaters and base stations for IMT, falling within the scope of one of the other parts of ETSI EN 301 908 [i.8], except for IMT-2000 FDMA/TDMA (DECT). The present document also covers the corresponding ancillary equipment. NOTE 1 - ETSI EN 301 908-10 [i.7] contains in particular requirements for radiated spurious emissions and control and monitoring functions applicable to IMT-2000 FDMA/TDMA (DECT) equipment. The present document includes technical requirements which are common to equipment falling within the scope of several of the other parts. It should be used in conjunction with at least another part of ETSI EN 301 908 [i.8]. NOTE 2 - The other parts of ETSI EN 301 908 [i.8], which are listed in the foreword of the present document, specify technical requirements in respect of a particular type of IMT equipment. NOTE 3 - Recommendations ITU R M.1457 15 [i.4], M.2012-4 [i.5] and M.2150.0 [i.10] define the characteristics of the members of the IMT-2000 family and IMT-Advanced respectively by means of references to technical specifications developed by Standards Development organizations. The present document applies to equipment designed to meet any version of the terrestrial specifications referenced in Recommendations ITU R M.1457 15 [i.4] and M.2012 4 [i.5]. The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference. NOTE 4 - The relationship between the present document and essential requirements of article 3.2 of Directive 2014/53/EU [i.1] is given in annex A.

Obsah

ČSN EN ISO 18314-2 This document specifies the Saunderson correction for different measurement geometries and the solutions of the Kubelka-Munk equation for hiding and transparent layers. It also specifies methods for the calculations of the tinting strength including the residual colour difference based on different criteria such as the depth of shade. Finally, methods for determining the hiding power are provided. The procedures for preparing the samples for these measurements are not part of this document. They are agreed between the contracting parties or are described in other national or international standards.

Obsah

ČSN EN ISO 17800 This document specifies the evaluation method of life cycle cost (LCC) and Life cycle assessment (LCA) of ductile iron pipes and fittings used for water applications and which are in compliance with EN 545. LCC evaluation is based on concepts and methods developed in ISO 15686-5. LCA evaluation is based on concepts and methods developed in ISO 15686-6, EN 15804:2012+A2:2019, EN ISO 14040 and EN ISO 14044. In this document, LCA is limited to the evaluation of environmental impact due to CO2 emissions associated with the consumption of natural resources or energy and waste disposal. The other categories of impacts are not in the scope of this document. Informative annexes are included in this document as a compilation of references, consensual factors, and scenarios with different DI pipelines.

Obsah

ČSN EN IEC 61987-31 This part of IEC 61987 provides - a characterization for the integration of infrastructure devices in the Common Data Dictionary (CDD); - generic structures in conformance with IEC 61987-10 for Operating Lists of Properties (OLOPs) and Device Lists of Properties (DLOPs) of infrastructure devices. The generic structures for the OLOP and DLOP contain the most important blocks for infrastructure devices. Blocks pertaining to a specific equipment type will be described in the corresponding part of the IEC 61987 series. Similarly, equipment properties are not part of this part of IEC 61987. For instance, the OLOP and DLOP for I/O-modules are to be found in IEC 61987-32.