Normy

Obsah

ČSN EN ISO 16890-3 This document specifies the test equipment and the test methods used for measuring the gravimetric efficiency and resistance to air flow of air filter for general ventilation. It is intended for use in conjunction with ISO 16890-1, ISO 16890-2 and ISO 16890-4. The test method described in this document is applicable for air flow rates between 0,25 m3/s (900 m3/h, 530 ft3/min) and 1,5 m3/s (5 400 m3/h, 3 178 ft3/min), referring to a test rig with a nominal face area of 610 mm x 610 mm (24 in x 24 in). This document refers to particulate air filter elements for general ventilation having an ePM1 efficiency less than or equal to 99 % and an ePM10 efficiency greater than 20 % when tested as per the procedures defined in the ISO 16890 series. NOTE - The lower limit for this test procedure is set at a minimum ePM10 efficiency of 20 % since it is very difficult for a test filter element below this level to meet the statistical validity requirements of this procedure. This document does not apply to filter elements used in portable room-air cleaners.

Obsah

ČSN EN 4500-001 The EN 4500 series specifies the rules for the drafting and presentation of metallic material standards for aerospace applications. This Part 001 specifies the "General rules" framework valid for all parts.

Obsah

ČSN EN 4500-002 The EN 4500 series specifies the rules for the drafting and presentation of metallic material standards for aerospace applications. This Part 002 specifies the "Specific rules for aluminium, aluminium alloys and magnesium alloys".

Obsah

ČSN EN 4500-003 The EN 4500 series specifies the rules for the drafting and presentation of metallic material standards for aerospace applications. This Part 003 specifies the "Specific rules for heat resisting alloys".

Obsah

ČSN EN 4827 This document specifies the requirements for hexavalent chromium free anodizing of aluminium and aluminium alloys for corrosion protection, bonding and painting. This document does not apply to hard anodizing and plasma electrolytic anodizing (micro-arc oxidation). The purpose of this document is to give design, quality and manufacturing requirements. It does not give complete in-house process instructions; these are given in the processor's detailed process instructions.

Obsah

ČSN P CEN/TS 17889 (38 3388) This document specifies classification, general requirements and test methods for flexible, factory made, buried district heating pipe systems with thermoplastic reinforced service pipes (TRSP). The factory made bonded or non-bonded flexible pipe systems covered by this document consist of: - a thermoplastic reinforced service pipe, which consists of an inner layer made of PE-Xa, a thermoplastic intermediate layer, a reinforcement layer made of para-aramid fibres, an outer thermoplastic layer and a diffusion barrier layer, all with bonded structure; - a thermal insulation layer; - a casing made of PE. Depending on the temperature profile, this document is applicable to a maximum operating temperature of 115 °C and maximum operating design pressure up to 1,6 MPa. The pipe systems are designed for a service life of at least 30 years. This document does not apply to cover surveillance systems. NOTE - For higher temperatures or for the transport of other fluids, for example potable water, additional requirements and testing is needed. Such requirements are not specified in this document. A guideline for testing the pipe assembly is given in Annex D.

Obsah

ČSN EN 12007-5 (38 6413) This document describes the specific functional requirements for the transportation of gases (gaseous energy carriers) through service lines in addition to the general functional requirements of EN 12007-1 for: a) a maximum operating pressure (MOP) up to and including 16 bar; b) an operating temperature between -20 °C and +40 °C; c) gases and blends of gases which are in the gaseous state when conveyed in the gas pipeline infrastructure such as hydrogen, hydrogen rich, and methane rich gases, dimethyl ether (DME) and propane and butanes used for combustion and/or as feedstock, excluding steam and compressed air, where technical evaluation has ensured that operating conditions, constituents and properties of the gas do not affect the safe operation and maintenance of the service line. It applies to their design, construction, commissioning, decommissioning, operation, maintenance, extension and other associated works including safety and environmental aspects. The service line is the physical asset comprising of pipework from the gas main branch saddle or top tee to the outlet of the distribution system operator's nominated point(s) of delivery (for example: isolation valve, regulator, meter connection or combination of regulator and isolation valve). This document does not apply retrospectively to installations before the publication date unless specifically stated. Specific functional requirements for: - polyethylene pipelines are given in EN 12007-2; - steel pipelines are given in EN 12007-3; - polyamide (PA-U) pipelines are given in CEN/TS 12007-6; - pipework for buildings are given in EN 1775; - pressure regulating installations are given in EN 12279 or EN 12186; - pressure testing, commissioning and decommissioning are given in EN 12327; - safety management system (SMS) and pipeline integrity management system (PIMS) are given in EN 17649. This document specifies common basic principles for gas infrastructure. Users of this document are expected to be aware that there can exist more detailed national standards and/or codes of practice in the CEN member countries. This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles. In the event of terms of additional requirements in legislation/regulation than in this document, CEN/TR 13737 (all parts) illustrates these terms. CEN/TR 13737 gives: - description of legislations/regulations applicable in a member state; - if appropriate, more restrictive national requirements; - a national contact point for the latest information.

Obsah

ČSN EN ISO 17174 This document specifies a method for the identification of single fish and fish fillets to the level of genus or species. It allows the identification of a large number of commercially important fish species using DNA barcoding. This method was validated on raw fish. Laboratory experience indicates additional applicability to processed fish products (e.g. cold smoked, hot smoked, salted, frozen, cooked, fried and deep-fried samples). The described method is usually unsuitable for the analysis of highly processed foods (e.g. tins of fish with highly degraded DNA where the fragment lengths are not sufficient for amplification of the targets). Furthermore, it does not apply to complex fish products containing mixtures of two or more fish species. The identification of fish species is carried out by PCR amplification of either a segment of the mitochondrial cytochrome b gene (cytb) or the cytochrome c oxidase I gene (cox1, syn COI), or both, followed by sequencing of the PCR products and subsequent sequence comparison with entries in databases.

Obsah

ČSN EN 13172 This document specifies common evaluation rules useful for the assessment and verification of constancy of performance of a thermal insulation product with harmonised technical specifications, product standards and any other assessment documents. Harmonised technical specifications, product standards and other assessment documents are called European product specifications in this document. This document applies to factory made products for buildings, factory made products for building equipment and industrial installations, in situ products for buildings, in situ products for building equipment and industrial installations, to products for civil engineering applications, and to external thermal insulation composite kits.

Obsah

ČSN EN 17818 Tento dokument stanovuje minimální požadavky pro systémy k úpravě vody, které vyrábějí účinnou látku - "aktivní chlor" - z chloridu sodného elektrolýzou pro provoz v místě použití (in situ). Účinná látka vyrobená v místě použití (IGAS), v tomto případě aktivní chlor, může být zavedena do roztoku ("off-line") nebo vyráběna přímo v potrubí ("in-line"). Tento dokument specifikuje požadavky na konstruci a zkušební metody pro zařízení používaná pro výrobu aktivního chloru v místě použití. Specifikuje požadavky pro pokyny k instalaci, provozu, údržbě, bezpečnosti a pro dokumentaci, která má být dodávána s výrobkem. Výroba účinných látek v místě použití a uvádění jejich prekurzorů na trh EU jsou předmětem specifikací nařízení o biocidních přípravcích (EU) 528/2012 ["Biocidní přípravky"]. Účinné látky vyrobené zařízeními, u kterých je deklarována shoda s tímto dokumentem, musí odpovídat BPR jak pro registrovaný aktivní chlor, normy kvality a prekurzor podle příslušného použití, tak pro "Typ produktu", který je uveden v BPR. Tato norma se nezabývá používáním zařízení pro výrobu aktivního chloru v místě použití. Rozsah užití pro výrobu chloru v místě použití je různý. Je odpovědností provozovatele/dodavatele výrobku, který deklaruje shodu s touto normou, aby zjistil příslušný druh systému a provozní podmínky pro specifické použití a: - specifikoval kvalitu biocidu vhodného pro použití. Ta může být stanovena v národních nebo mezinárodních normách; - specifikoval příslušný typ produktu a provozní podmínky (koncentraci, dávkování a kvalitu aktivního chloru); - specifikoval další požadavky právních předpisů relevantních pro specifické použití; - specifikoval vhodný prekurzor chloridu sodného, pro použití; - a příslušně označil produkt.

Obsah

ČSN EN ISO 17294-1 Tento dokument specifikuje podstatu hmotnostní spektrometrie s indukčně vázaným plazmatem (ICP-MS) a uvádí obecné pokyny k použití této metody pro stanovení prvků ve vodě, v digestátech (roztocích po rozkladu) kalů a sedimentů (např. v digestátech vody, jak je popsáno v ISO 15587-1 nebo ISO 15587-2). Toto měření se obvykle provádí ve vodě, ale je možné zahrnout také plyny, páry nebo jemné nerozpuštěné částice. Tento dokument platí pro používání ICP-MS pro analýzu vodných roztoků. Konečné stanovení prvků je popsáno v samostatné normě pro každou řadu prvků a matrici. Jednotlivé kapitoly tohoto dokumentu odkazují uživatele na tento návod obsahující podstatu metody a uspořádání přístroje.

Obsah

ČSN EN ISO 7199 This document specifies requirements for sterile, single-use, extracorporeal blood-gas exchangers (oxygenators) intended for the supply of oxygen to, and the removal of carbon dioxide from, human blood, during cardiopulmonary bypass (CPB) for up to 6 h, extracorporeal lung assist [ECLA with veno-venous (VV), veno-arterial (VA) or veno-arterial-venous (VAV) cannulation strategies], cardiopulmonary support (CPS), extracorporeal life support (ECLS with VA cannulation strategy), extracorporeal carbon dioxide removal (ECCO2R), and other extracorporeal circulation techniques requiring blood-gas exchange. This document also applies to heat exchangers and arterial filters that are integral parts of the oxygenator. This document also applies to external equipment unique to the use of the oxygenator. This document does not apply to - implanted oxygenators, - liquid oxygenators, - extracorporeal circuits (blood tubing), - separate heat exchangers, - separate ancillary devices, and - separate arterial line filters.