Normy

Obsah

ČSN EN 14917 This document specifies the requirements for design, manufacture and installation of metal bellows expansion joints with circular cross section for pressure applications with maximum allowable pressure greater than 0,5 bar.

Obsah

ČSN EN IEC 62290-3 Tato část souboru IEC 62290 určuje architekturu systémů řízení městské dopravy s vyhrazenou vodicí dráhou (UGTMS) stanovených v IEC 62290-1 a IEC 62290-2 a přiřazení funkcí a požadavků stanovených v IEC 62290-2 různým subsystémům UGTMS (označených jako systémové prvky v IEC 62290-1 a IEC 62290-2), používaných na tratích a sítích městské hromadné dopravy s vyhrazenou vodicí dráhou. Norma platí pro nové tratě nebo pro modernizace stávajících systémů návěštění a řízení. Dále norma platí pro nepřetržitý přenos dat, nepřetržitý dohled nad pohybem vlaku prostřednictvím dynamických rychlostních profilů, určování polohy komunikujících vlaků a volitelně nekomunikujících vlaků prostřednictvím vnějšího traťového zařízení (např. při smíšeném nebo omezeném provozu). Norma neplatí pro stávající systémy řízení a kontroly nebo projekty zahájené před datem platnosti tohoto dokumentu.

Obsah

ČSN EN IEC 62439-3 ed. 4 The IEC 62439 series is applicable to high-availability automation networks based on the Ethernet technology. This document: - specifies PRP and HSR as two related redundancy protocols designed to provide seamless recovery in case of single failure of an inter-bridge link or bridge in the network, which are based on the same scheme: parallel transmission of duplicated information; - specifies the operation of the precision time protocol (PTP) in networks that implement the two redundancy protocols (Annex A); - specifies PTP profiles with performance suitable for power utilty automation (Annex B) and industrial automation (Annex C); - includes for better understanding a tutorial (Annex D) on the PTP features effectively used in high-availability automation networks; - includes a management information base for PTP (Annex E); - defines a conformance test suite for the above protocols (Annex F).

Obsah

ČSN EN IEC 61968-100 ed. 2 This part of IEC 61968 defines how messages may be exchanged between cooperating systems in order to facilitate the transfer of application-specific data. Such application-specific data include but are not limited to the message payloads defined in IEC 61968 (Parts 3 to 9 and Part 13), IEC 61970 and IEC 62325. This document provides normative definitions for: - a set of message archetypes (Clause 5); - a set of message exchange patterns that both sending and receiving systems are expected to implement (Clause 6); - the exact format of the messages that are to be transmitted over the various integration technologies including a precise description of the information that each message must contain (Clause 7); - a set of constraints and conventions to which applications must adhere in order to facilitate message exchange using IEC 61968-100 (Clause 8); - the details of how IEC 61968-100 messages should be implemented using various underlying transport mechanisms (Clause 9).

Obsah

ČSN ETSI EN 300 175-8 V2.9.1 The present document is one of the parts of the specification of the Digital Enhanced Cordless Telecommunications (DECT) Common Interface (CI). This part of the DECT CI specifies the speech and audio coding and transmission requirements. In order to ensure satisfactory interworking of different portable and fixed units, it is necessary to specify the transmission performance of the analog information over the digital link. This requires not only use of a common speech algorithm, but also standardization of frequency responses, reference speech levels (or loudness) at the air interface and various other parameters. The present document applies to DECT equipment which includes all the necessary functions to provide real time two way speech conversation and stereo audio transmission. Several speech services are defined in the present document, including conventional 3,1 kHz telephony, wideband 7 kHz voice transmission, super-wideband 14 kHz and fullband 20 kHz service. DECT Fixed part providing such services may be connected to the public circuit switched (PSTN/ISDN) network, to private networks or to the Voice over Internet Protocol (VoIP) network. Tethered fixed point local loop applications are not required to comply with the requirements of the present document. For the DECT systems which connect to the Public Switched Telephone Network (PSTN) via an analog interface, the additional requirements, which are implemented in the FP, have as much as possible been aligned with ETSI TBR 038 [29]. A summary of the control and the use of the DECT echo control functions, to guide on need for options to manufacturers and installers, is found in annex A. Information concerning test methods can be found in ETSI EN 300 176-1 [9] and ETSI EN 300 176-2 [10] (previously covered by ETSI TBR 010 [i.5]). The test methods take into account that DECT is a digital system. The present document includes New Generation DECT, a further development of the DECT standard introducing wideband speech, improved data services, new slot types and other technical enhancements. In addition, the present document includes DECT Evolution, providing SWB and FB speech and audio capabilities and a new speech coding algorithm for NB and WB allowing to increase the audio quality of the NB and WB speech service and improve bandwidth efficiency. The latest update for DECT Evolution includes the support of ultra-band, high resolution, low-latency speech and audio coding, and additional PP types supported with LC3plus coding. An application profile using these new PP types can be found in ETSI TS 103 706 [i.28].

Obsah

ČSN ETSI 303 105-1 V1.1.1 Tento dokument popisuje přenosový systém pro digitální zemské a hybridní (kombinace zemského a družicového přenosu) vysílání pro ruční koncová zařízení. Stanovuje celou část fyzické vrstvy od vstupních toků po přenášený signál. Tento přenosový systém je určen pro přenos transportních toků nebo generických datových toků napájejících lineární nebo nelineární aplikace, jako jsou televizní, rádiové a datové služby. Koncová zařízení DVB-NGH by mohla rovněž zpracovávat signály DVB-T2.

Obsah

ČSN EN IEC 62271-4 ed. 2 Tato část IEC 62271 platí pro postupy pro manipulaci s izolačními a/nebo spínacími plyny při instalaci, uvádění do provozu, opravách, generálních opravách, běžném a mimořádném provozu a likvidaci po skončení životnosti energetických zařízení. Tyto postupy jsou považovány za minimální požadavky k zajištění spolehlivosti elektroenergetických zařízení, bezpečnosti personálu pracujícího s těmito plyny a minimalizace dopadu na životní prostředí. Další požadavky mohou být uvedeny nebo specifikovány v návodu k obsluze výrobce. Pro každý plyn, o němž je známo, že se v elektroenergetických zařízeních používá k datu vydání tohoto dokumentu, jsou v samostatné příloze popsány specifikace, postupy manipulace, bezpečnostní opatření atd. U plynů, které nejsou zahrnuty v těchto přílohách, by měl výrobce elektrického zařízení poskytnout potřebné informace podle struktury těchto příloh. Tyto plyny by měly být rovněž popsány v dalším vydání nebo ve změnách tohoto vydání.

Obsah

ČSN EN 16602-70-61 This Standard defines the technical requirements and quality assurance provisions for the manufacture and verification of high-reliability electronic circuits of surface mount, through hole, solderless assemblies and soldering of harness and wire interconnection. The Standard defines workmanship requirements, the acceptance and rejection criteria for high-reliability assemblies intended to withstand ground testing conditions including LTS (long term storage) and the environment imposed by space flight and launchers. The mounting and supporting of components, terminals and conductors specified in this standard applies only to assemblies designed to continuously operate over the mission within the temperature limits of -55 °C to +85 °C at solder joint level. Requirements related to printed circuit boards are contained in ECSS-Q-ST-70-60 and ECSS-Q-ST-70-12. This standard does not cover lead-free soldering and associated requirements. This Standard does not cover the qualification and acceptance of the EQM and FM equipment with high-reliability electronic circuits of surface mount, through hole and solderless assemblies. This Standard does not cover verification of thermal properties for component assembly. This Standard does not cover pressfit connectors due to the possible damage in the PCB that is not evaluated within this test requirement. The qualification and acceptance tests of equipment manufactured in accordance with this Standard are covered by ECSS-E-ST-10-03. This standard may be tailored for the specific characteristics and constraints of a space project, in accordance with ECSS-S-ST-00.

Obsah

ČSN EN IEC 61158-5-2 ed. 5 The fieldbus application layer (FAL) provides user programs with a means to access the fieldbus communication environment. In this respect, the FAL can be viewed as a "window between corresponding application programs." This part of IEC 61158 provides common elements for basic time-critical and non-time-critical messaging communications between application programs in an automation environment and material specific to Type 2 fieldbus. The term "time-critical" is used to represent the presence of a time-window, within which one or more specified actions are required to be completed with some defined level of certainty. Failure to complete specified actions within the time window risks failure of the applications requesting the actions, with attendant risk to equipment, plant and possibly human life.

Obsah

ČSN P ISO/TS 5206-1 Tento dokument vymezuje termíny, charakteristiku a vztahy konceptů, které jsou stanoveny pomocí metod architektury postavené na modelu, pro parkování a činnosti související s parkováním (uliční i na parkovacích plochách), včetně podpory pro výměnu společných dat mezi podniky a poskytování služeb koncovým uživatelům.

Obsah

ČSN EN 12896-10 The main objective of the present standard is to present the Reference Data Model for Public Transport, based on: - the Reference Data Model, EN12896, known as Transmodel V6, incorporating the requirements of - EN 15531-1 to -3 and TS 15531-4 and -5: Service interface for real-time information relating to public transport operations (SIRI), - TS 16614-1 to 5: Network and Timetable Exchange (NeTEx). A particular attention is drawn to the data model structure and methodology: - the data model is described in a modular form in order to facilitate the understanding and the use of the model, - the data model is entirely described in UML. In particular, a Reference Data Model kernel is described, referring to the data domain: - Network Description: routes, lines, journey patterns, timing patterns, service patterns, scheduled stop points and stop places. Furthermore, the following functional domains are considered: - Timing Information and Vehicle Scheduling (runtimes, vehicle journeys, day type-related vehicle schedules) - Passenger Information (planned and real-time) - Fare Management (fare structure, sales, validation, control) - Operations Monitoring and Control: operating day-related data, vehicle follow-up , control actions - Management Information and Statistics (including data dedicated to service performance indicators). - Driver Management: - Driver Scheduling (day-type related driver schedules), - Rostering (ordering of driver duties into sequences according to some chosen methods), - Driving Personnel Disposition (assignment of logical drivers to physical drivers and recording of driver performance). This part corresponds to the Transmodel V6.0 Alternative Modes The data modules dedicated to cover most functions of the above domains are specified. Several concepts are shared by the different functional domains. This data domain is called "Common Concepts".

Obsah

ČSN EN 16603-20-08 This Standard specifies the general requirements for the qualification, procurement, storage and delivery of photovoltaic assemblies, solar cell assemblies, bare solar cells, coverglasses, protection diodes and planar blocking diodes suitable for space applications. This standard does not cover the particular qualification requirements for a specific mission. This Standard is primarily applicable for qualification approval for photovoltaic assemblies, solar cell assemblies, bare solar cells, coverglasses, protection diodes and planar blocking diodes, and to the procurement of these items. This standard is limited to crystalline Silicon and single and multi-junction GaAs solar cells with a thickness of more than 50 µm and does not include thin film solar cell technologies and poly-crystalline solar cells. This Standard does not cover the concentration technology, and especially the requirements related to the optical components of a concentrator (e.g. reflector and lens) and their verification (e.g. collimated light source). This Standard is not applicable for qualification of the solar array subsystem, solar panels, structure and solar array mechanisms. This standard may be tailored for the specific characteristic and constrains of a space project in conformance with ECSS-S-ST-00. Qualification is a process to confirm compliance with requirements that have been established with reference to foregoing characterization and engineering test programs. Guidelines for characterization and engineering tests and for relaxation of qualification tests due to similarity with earlier performed qualification are described in the handbook ECSS-E-HB-20-08. Those clauses in this standard, for which the Handbook gives additional information, will refer to the Handbook.