Normy

Obsah

ČSN EN 62808 This International Standard establishes requirements for the design, analysis and qualification of isolation devices used to ensure electrical independence of redundant safety systém circuits, or between safety and lower class circuits, as specified in IEC 60709. This standard includes guidance on the determination of the maximum credible fault that is applied to the isolation devices. The maximum credible fault can be used as a basis for the test levels used in testing based on other standards (e.g. IEC TS 61000-6-5 or IEC 62003). This standard does not address safety or CCF issues due to functional inter-dependencies and possible interfe-rences or CCFs that may result from signal exchange or sharing between systems or sub-systems. It also does not address design or qualification issues related todigital or programmable logic in isolation devices. For isolation devices containing digital or programmable logic, additional design and qualification requirements must be considered; these requirements are outside the scope of this standard.

Obsah

ČSN EN 60838-2-3 This part of IEC 60838-2 applies to lampholders for double-capped linear LED lamps intended for building-in (to be used for general lighting service and with caps as listed in Annex A). Lampholders within the scope of this standard do not include heat management. Double-capped linear LED lamps can also be used with lampholders originally been designated for other technologies. The requirementsfor these lampholders are covered by separate standards.

Obsah

ČSN EN 62922 Tento dokument uvádí výkonnostní požadavky OLED dlaždic a panelů používaných na stejnosměrné napájení až do 120 V nebo na střídavé napájení až do 50 V při 50 Hz nebo 60 Hz pro vnitřní osvětlení a obdobné všeobecné osvětlovací účely.

Obsah

ČSN EN 61853-2 The IEC 61853 series establishes IEC requirements for evaluating PV module performance based on power (watts), energy (watt-hours) and performance ratio (PR). It is written to be applicable to all PV technologies, but may not work well for any technology where the module performance changes with time (e.g. modules change their behaviour with light or thermal exposure), or which experience significant non-linearities in any of their characteristics used for the modelling. The purpose of this part of IEC 61853 is to define measurement procedures for measuring the effects of angle of incidence of the irradiance on the output power of the device, to determine the operating temperature of a module for a given set of ambient and mounting conditions and measure spectral responsivity of the module. A second purpose is to provide a characteristic set of parameters which will be useful for detailed energy predictions. The described measurements are required as inputs into the module energy rating procedure described in IEC 61853-3.

Obsah

ČSN EN 62788-1-4 IEC 62788-1-4:2016 provides a method for measurement of the optical transmittance of encapsulation materials used in photovoltaic (PV) modules. The standardized measurements in this procedure quantify the expected transmittance of the encapsulation to the PV cell. Subsequent calculation of solar-weighted transmittance allows for comparison between different materials. The results for unweathered material may be used in an encapsulation manufacturer's datasheets, in manufacturer's material or process development, in manufacturing quality control (material acceptance), or applied in the analysis of module performance. This measurement method can also be used to monitor the performance of encapsulation materials after weathering, to help assess their durability.

Obsah

ČSN EN ISO 12625-6 This document specifies a test method for the determination of grammage of tissue paper and tissue products.

Obsah

ČSN EN 16727-3 This European Standard specifies minimum requirements and other criteria for assessing the general safety and environmental performance of noise barriers and related devices acting on airborne sound propagation under typical rail-side conditions. Requirements for more onerous conditions are a matter for consideration by the designer. Appropriate test methods are provided where these are necessary, but for some aspects a declaration of material characteristics may be required for the information of designers. The treatment of each topic is covered separately in Annexes A to G.

Obsah

ČSN EN 16725 Tato evropská norma se vztahuje na obnovu odlévané austenitické manganové oceli pro pevné srdcovky a rámy pro srdcovky s pohyblivým hrotem, které mají být přivařeny odtavovacím stykovým svařováním nebo sešroubovány za účelem připojení k sousedním kolejnicím podle normy ČSN EN 15689. Tato norma se rovněž vztahuje na navařování konců srdcovek z austenitické manganové oceli přivařených prostřednictvím příslušné trimetalové oblasti. Norma specifikuje systémy pro schvalování svařovacího materiálu a postupů používaných při ručním obloukovém svařování a při opravném obloukovém svařování tavící se plněnou elektrodou. Norma obsahuje úkoly a povinnosti související s kvalitou a kvalifikací pracovníků provádějících opravné navařování odlévaných srdcovek elektrickým obloukem. Dovolený svařovací proces je omezen na svařování elektrickým obloukem (EA) v souladu s normou EN ISO 4063, konkrétně se jedná o metody číslo 111 "MMA" (ruční obloukové svařování obalenou elektrodou) a číslo 114 "FCAW" (obloukové svařování plněnou elektrodou bez ochranného plynu). V uvedené normě je popsáno jejich použití. Postupy uvedené v této normě mohou být aplikovány na práce v trati nebo i v místech mimo trať. Účelem této normy je sjednotit obnovu odlévaných manganových srdcovek navařováním elektrickým obloukem napříč Evropou. Norma uvádí řídicí systémy pro schvalování a kvalifikaci svařovacích procesů, specifikací postupu svařování (WPS), přídavného svařovacího materiálu, dodavatelů a svářečů za účelem úspěšného zhotovení návarů na provozovaných srdcovkách.

Obsah

ČSN ETSI EN 301 489-29 V2.1.1 The present document together with ETSI EN 301 489-1 [1], covers the assessment of all radio transceivers associated with Ultra Low Power Active Medical Implants (ULP-AMIs), Ultra Low Power Active Medical Devices (ULP-AMDs), Ultra Low Power Body Worn Devices (ULP-BWDs) and associated Ultra Low Power Active Medical Implant Peripherals (ULP-AMI-Ps), Ultra Low Power Active Medical Device Peripherals (ULP-AMD-Ps) in respect of ElectroMagnetic Compatibility (EMC). The radio link may be part of life supporting or non life supporting equipment and can be classified independently of the classification of the medical portion of the device. The present document covers the EMC requirements for the radio functions of ultra low power implanted, body worn and associated ultra low power peripheral devices. Technical specifications related to the antenna port and emissions from the enclosure port of these radio system devices are not included in the present document. Such technical specifications are found in the relevant product standards for the effective use of the radio spectrum. The present document applies to ULP-AMI, ULP-AMD, ULP-BWD, ULP-AMD-P and ULP-AMI-P devices with RF power levels ranging up to 25 µW ERP and intended for operation in the frequency range 401 MHz to 402 MHz and 405 MHz to 406 MHz in accordance with the provisions of annex 12, band b) and band c), to CEPT/ERC/REC 70 03 [i.3]. Definitions of such ULP-AMI, ULP-AMD, ULP-BWD, ULP-AMD-P and ULP-AMI-P radio devices are found in the following functional radio standard: ETSI EN 302 537 [2]: "Ultra Low Power Medical Data Service (MEDS) Systems operating in the frequency range 401 MHz to 402 MHz and 405 MHz to 406 MHz; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU". In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present document and ETSI EN 301 489 1 [1], the provisions of the present document take precedence. The environmental classification and the emission and immunity requirements used in the present document are as stated in the ETSI EN 301 489 1 [1], except for any special conditions included in the present document. The present document, together with ETSI EN 301 489-1 [1], are aimed to cover requirements to demonstrate an adequate level of electromagnetic compatibility.

Obsah

ČSN ETSI EN 301 489-27 V2.1.1 The present document together with ETSI EN 301 489-1 [1], covers the assessment of all radio transceivers associated with Ultra Low Power Active Medical Implants (ULP-AMIs) and associated Peripheral ULP-AMI-Ps) in respect of ElectroMagnetic Compatibility (EMC). The present document covers the EMC requirements for the radio functions of ULP-AMI and ULP-AMI-P devices. Technical specifications related to the antenna port and emissions from the enclosure port of the ULP-AMI and ULP-AMI-P devices radio system are not included in the present document. Such technical specifications are found in the relevant product standards for the effective use of the radio spectrum. The present document specifies the applicable test conditions, performance assessment, and performance criteria for ULP-AMIs and associated Peripheral devices (ULP-AMI-Ps). Definitions of types of ULP-AMIs and ULP-AMI-Ps covered by present document are given in annex B. In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present document and ETSI EN 301 489-1 [1], the provisions of the present document take precedence. The environmental classification and the emission and immunity requirements used in the present document are as stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document. The present document, together with ETSI EN 301 489-1 [1], contains requirements to demonstrate an adequate level of electromagnetic compatibility as set out in Directive 2014/53/EU [i.1].

Obsah

ČSN ETSI EN 301 489-35 V2.1.1 The present document together with ETSI EN 301 489-1 [1], covers the assessment of all radio transceivers associated with Low Power Active Medical Implants (LP-AMIs) and associated Peripheral devices (LP-AMI-P) in respect of ElectroMagnetic Compatibility (EMC). The present document covers the EMC requirements for the radio functions of LP-AMI and associated Peripheral devices (LP-AMI-P). Technical specifications related to the antenna port and emissions from the enclosure port of the radio system of LP AMI and associated Peripheral devices (LP-AMI-P) are not included in the present document. Such technical specifications are found in the relevant product standards for the effective use of the radio spectrum. The present document specifies the applicable test conditions, performance assessment, and performance criteria for of LP-AMI and associated Peripheral devices (LP-AMI-P). Definitions of types of LP-AMIs and P-AMI-Ps covered by present document are given in annex B. In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present document and ETSI EN 301 489 1 [1], the provisions of the present document take precedence. The environmental classification and the emission and immunity requirements used in the present document are as stated in the ETSI EN 301 489 1 [1], except for any special conditions included in the present document. The present document, together with ETSI EN 301 489-1 [1], contains requirements to demonstrate an adequate level of electromagnetic compatibility as set out in Directive 2014/53/EU [i.1].

Obsah

ČSN ETSI EN 302 609 V2.1.1 The present document covers the technical requirements for radio transmitters and receivers used in the Euroloop transmission system. The system is used in railway systems. The present document applies to the following equipment: " The On-Board Equipment (OBE) receiving the Euroloop signal and the OBE comprises a receiver fitted with a dedicated antenna. " The Track-Side Equipment (Euroloop) transmitting the Euroloop signal that is always installed in an inner or outer foot of a rail. The Euroloop transmission system operates in frequency bands listed in table 1 in accordance with the EC Decision 2013/752/EU [i.2], and ERC Recommendation 70-03 [i.3], annex 4. The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference.