Normy

Obsah

ČSN EN ISO 11111-1 Tato část ISO 11111 specifikuje bezpečnostní požadavky pro často se vyskytující společná nebezpečí textilních strojů a nebezpečí určitých prvků strojů jsou zahrnuta v ISO 11111-2 až ISO 11111-7. Tato řada norem je doplněna normami typu C ISO 9902 (všechny části), pokud jde o měření emisí hluku a ISO 23771, pokud jde o opatření na snížení emisí hluku.

Obsah

ČSN ETSI EN 302 208 V3.1.1 The present document covers the minimum characteristics considered necessary in order to make the best use of the available frequencies. It does not necessarily include all the characteristics that may be required by a user, nor does it necessarily represent the optimum performance achievable. Radio frequency identification products covered within the present document are considered by definition short-range devices. Power limits up to a maximum of 2 W e.r.p. are specified for this equipment in the frequency band 865 MHz to 868 MHz and up to a maximum of 4 W e.r.p. in the frequency band 915 MHz to 921 MHz. The frequency usage conditions for RFIDs in the band 865 MHz to 868 MHz are EU wide harmonised according to 2006/804/EC [i.12]. It should be noted that the frequency band 915 MHz to 921 MHz has only a limited implementation status within the European Union and the CEPT countries. ERC/REC 70-03 [i.9] provides in appendix 1 an overview of countries where the band is implemented. The present document applies to RFID interrogators and tags operating together as a system. For each specified band, four high power channels are made available for use by interrogators. The tags respond with a modulated signal preferably in the adjacent low power channels. Interrogators may be used with either integral or external antennas. The types of equipment covered by the present document are as follows: - fixed interrogators; - portable interrogators; - batteryless tags; - battery assisted tags; - battery powered tags. The present document contains requirements to demonstrate that the specified radio equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference.

Obsah

ČSN ETSI EN 303 883 V1.1.1 Tento dokument shrnuje dostupné informace o možných technikách a postupech měření pro měření shody různých formátů signálu UWB za účelem splnění daných přenosových limitů uvedených ve stávajícím nařízení. Tento dokument se bude využívat jako referenční pro existující a budoucí normy ETSI zahrnující technologie UWB.

Obsah

ČSN EN 62580-1 Norma definuje obecnou architekturu palubních multimediálních a telematických subsystémů (OMTS) tak, aby bylo dosaženo kompatibility mezi subsystémy ve stejném vozidle a mezi subsystémy na palubě různých vozidel ve stejném vlaku. Specifikuje obecnou architekturu palubního multimediálního a telematického subsystému, který obsahuje čtyři kategorie multimediálních a telematických subsystémů definovaných jako: A: Video dohled/ CCTV B: Služby orientované na strojvedoucího a posádku C: Služby orientované na cestující D: Služby orientované na provozovatele a údržbu vlaku Stanovuje hranici mezi OMTS a palubním komunikačním systémem popsaným v souboru IEC 61375, metodiku pro popis OMTS z hlediska abstraktního modelu, obecné zásady a základní požadavky na specifikaci služeb poskytovaných/požadovaných každou kategorií, přístup pro zajištění interoperability mezi službami. Poskytuje obecné zásady pro klasifikaci OMTS, strukturování funkčního rozčlenění, strukturování rozčlenění systému, formální specifikaci OMTS. Vztahuje na jakýkoliv typ vlaku, např. otevřené vlaky, vlaky z více jednotek a uzavřené vlaky.

Obsah

ČSN ETSI EN 301 166 V2.1.1 The present document covers the technical requirements for radio transmitters and receivers used in stations in the Private Mobile Radio (PMR) service. It applies to use in the land mobile service, operating on radio frequencies between 30 MHz and 3 GHz, with narrow channel separations (CSP) (less than 10 kHz) and intended for speech and/or data. It is the intention of the present document to cover any Channel Bandwidths (CBW) permitted by National Administrations for such systems, e.g. 6,25 kHz. In the present document different requirements are given for the different radio frequency bands, environmental conditions and types of equipment where appropriate. In the present document, data transmission systems are defined as systems which transmit and/or receive data and/or digitized voice. The equipment comprises a transmitter and associated encoder and modulator and/or a receiver and associated demodulator and decoder. The present document covers equipment which may use constant envelope or non-constant envelope modulation. The types of equipment covered by the present document are as follows: - base station: equipment fitted with antenna connector; - mobile station: equipment fitted with antenna connector. Handportable stations: a) either fitted with an antenna connector; or b) without an external antenna connector but fitted with a permanent internal or a temporary internal 50 RF connector which allows access to the transmitter output and the receiver input. Handportable station equipment without an external or internal Radio Frequency (RF) connector and without the possibility of having a temporary internal 50 RF connector is not covered by the present document. The present document contains requirements to demonstrate that "... Radio equipment shall be so constructed that it both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference" and that "....radio equipment supports certain features ensuring access to emergency services" [i.3]. In addition to the present document, other ENs (e.g. ETSI EN 301 489-1 [i.4] and ETSI EN 301 489-5 [i.5]) that specify technical requirements in respect of essential requirements under the Radio Equipment Directive [i.3], may apply to equipment within the scope of the present document.

Obsah

ČSN ETSI EN 303 978 V2.1.2 The present document applies to Earth Stations on Mobile Platforms (ESOMP), which have the following characteristics. - The ESOMP is designed for both mobile and stationary operation. - The ESOMP operates on various mobile platforms such as trains, maritime vessels, aircraft and other vehicles and, therefore, may be subject to occasional disturbances and interruptions in the satellite link. - The ESOMP is operating as part of a satellite network (e.g. star, mesh or point to point) used for the distribution and/or exchange of information. - The ESOMP is comprised of all the equipment, electrical and mechanical, from the antenna itself to the interface with other communications equipment on a mobile platform (usually referred to as the terrestrial interface). - The ESOMP transmits within the frequency range from 27,50 GHz to 30,00 GHz, which is a band allocated to the Fixed Satellite Services (FSS) (Earth to space) among other services. However, operation of the ESOMP is intended to be restricted to the frequency range 29,50 GHz to 30,00 GHz in and near those countries that have allocated Fixed Service (FS) to the other frequency ranges. Local regulation may permit operation in these frequency ranges. - The ESOMP receives in one or more frequencies within the range from 17,30 GHz to 20,20 GHz (FSS). - The ESOMP uses linear or circular polarization. - The ESOMP operates through a geostationary satellite (or a cluster of co-located geostationary satellites) that is at least 2° away from any other geostationary satellite operating in the same frequencies and over the same coverage area. NOTE 1: ESOMPs may operate with satellites that are more closely spaced than 2° with additional operational constraints that are beyond the scope of the present document. - The ESOMP is designed for unattended operation. - The ESOMP is controlled and monitored by a Network Control Facility (NCF). This function may be performed centrally (e.g. for a network of ESOMPs with a central hub) or it could be performed within the ESOMP for autonomous control. The NCF is outside the scope of the present document. The present document applies to the ESOMP with its ancillary equipment and its various telecommunication ports, and when operated within the boundary limits of the operational environmental profile as declared by the applicant and when installed as required by the applicant's declaration or in the user documentation. The present document is intended to cover the provisions of Directive 2014/53/EU [i.11] (RE Directive) article 3.2, which states that ". radio equipment shall be so constructed that it both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference". NOTE 2: Operational requirements are defined by national administrations and by relevant ECC Decisions. In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the Directive 2014/53/EU [i.11] may apply to equipment within the scope of the present document. NOTE 3: A list of such ENs is included on the web site http://www.newapproach.org/.

Obsah

ČSN ISO 10241-1 Tato norma specifikuje požadavky na navrhování a strukturování terminologických hesel v technických normách a uvádí příklady z dokumentů ISO a IEC. Termíny a jiná označení vyskytující se v terminologických heslech mohou obsahovat písmena, číslice, matematické značky, typografické znaky a syntaktické znaky (např. interpunkční znaménka, spojovníky a pomlčky, kulaté a hranaté závorky a jiné spojovací nebo oddělovací znaky), někdy ve znakových stylech (tj. fonty a tučné písmo, kurziva, tučná kurziva nebo jiné stylové zvyklosti), které se řídí zvyklostmi specifickými pro daný jazyk, doménu nebo předmět. Termíny mohou rovněž zahrnovat normalizované značky (které mohou být jazykově nezávislé nebo mezinárodně harmonizované, jako jsou např. značky pro veličiny a jednotky a také grafické značky), za něž odpovídají jiné komise ISO a IEC. Norma je založena na principech a metodách uvedených v ISO 704 a uvádí pravidla jak pro jednojazyčná, tak pro vícejazyčná terminologická hesla v technických normách a v jejich rejstřících.

Obsah

ČSN ETSI EN 303 979 V2.1.2 The present document applies to Earth Stations on Mobile Platforms (ESOMP), which have the following characteristics. - The ESOMP is designed for both mobile and stationary operation. - The ESOMP operates on various mobile platforms such as trains, maritime vessels, aircraft and other vehicles and, therefore, may be subject to occasional disturbances and interruptions in the satellite link. - The ESOMP is operating as part of a satellite network (e.g. star, mesh or point to point) used for the distribution and/or exchange of information. - The ESOMP is comprised of all the equipment, electrical and mechanical, from the antenna itself to the interface with other communications equipment on a mobile platform (usually referred to as the terrestrial interface). - The ESOMP comprises of one or more emitters and the system overview given in figure 1 should be interpreted accordingly. - The ESOMP transmits within the frequency range from 27,5 GHz to 29,1 GHz and 29,5 GHz to 30,0 GHz, which is a band allocated to the Fixed Satellite Services (FSS) (Earth to space) among other services. National regulations will specify the bands available for the operation of the ESOMP. Such regulations may designate some parts of the frequency range 27,5 GHz to 29,1 GHz to terrestrial services such as the Fixed Service. However, the operation of the ESOMP may be permitted under national regulations in the 29,50 GHz to 30,00 GHz band since this band is allocated on a primary basis to the Fixed Satellite Service. - The ESOMP receives in one or more frequencies within the range from 17,30 GHz to 20,20 GHz (FSS). - The ESOMP uses linear or circular polarization. - The ESOMP operates through non-geostationary satellites. - The ESOMP is designed for unattended operation. - The ESOMP is controlled and monitored by a Network Control Facility (NCF). This function may be performed centrally (e.g. for a network of ESOMPs with a central hub) or it could be performed within the ESOMP for autonomous control. The NCF is outside the scope of the present document. - The ESOMP operating in the 27,5 GHz to 28,6 GHz and 29,5 GHz to 30 GHz bands: epfd limits given in article 22 of the ITU Radio Regulations [i.4] apply for the ESOMPs operating with the NGSO system for the protection of the GSO networks (see No 22.5D of the ITU RR [i.4]). - ESOMP operating in the 28,6 GHz to 29,1 GHz band: No 9.11A of the ITU RR [i.4] applies to the NGSO network of the ESOMP, meaning that the NGSO will be required to coordinate with earlier filed GSO networks or NGSO systems (See No. 5.523A of the ITU RR [i.4]). The present document applies to the ESOMP with its ancillary equipment and its various telecommunication ports, and when operated within the boundary limits of the operational environmental profile as declared by the applicant and when installed as required by the applicant's declaration or in the user documentation. The present document is intended to cover the provisions of Directive 2014/53/EU [i.6] (RE Directive) article 3.2, which states that ". radio equipment shall be so constructed that it both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference". NOTE 1: Operational requirements are defined by national administrations and by relevant ECC Decisions. In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the Directive 2014/53/EU [i.6] may apply to equipment within the scope of the present document. NOTE 2: A list of such ENs is included on the web site http://www.newapproach.org/.

Obsah

ČSN ETSI EN 300 674-2-2 V2.1.1 Tento dokument platí pro systémy telematiky v dopravě a provozu (TTT): - s připojením vysokofrekvenčního výstupu a specifikovanou anténou nebo s vestavěnou anténou; - pouze pro přenos dat; - pracující na rádiových kmitočtech v kmitočtovém pásmu pro zařízení krátkého dosahu 5 725 MHz až 5 875 MHz. Tento dokument je využitelný pouze pro palubní jednotky (OBU) a neobsahuje nutně všechny vlastnosti, které může požadovat uživatel, ani nutně nepředstavuje optimální dosažitelnou funkčnost. Splňuje rozhodnutí Komise 2013/752/EU a doporučení CEPT/ERC 70-03. Je specifickou normou pokrývající různé aplikace TTT. Tento dokument obsahuje požadavky k prokázání, že rádiové zařízení účinně využívá jak rádiového spektra, tak podporuje jeho účelné využívání, aby se zabránilo škodlivým interferencím.

Obsah

ČSN EN ISO 25237 ISO 25237:2017 contains principles and requirements for privacy protection using pseudonymi-zation services for the protection of personal health information. This document is applicable to organizations who wish to undertake pseudonymization processes for themselves or to organizations who make a claim of trustworthiness for operations engaged in pseudonymization services.

Obsah

ČSN EN 61000-1-2 Tato část souboru norem stanoví metodiku pro dosažení funkční bezpečnosti pouze s ohledem na elektro-magnetický jev. Tato metodika zahrnuje důsledek, který má na zařízení použité v takových systémech a in-stalacích. Norma: a) se použije na systémy a instalace souvisící s bezpečností, které zahrnují elektric-ké/elektronické/programovatelné zařízení instalované a používané v souladu s provozními podmínkami; b) zvažuje vliv elektromagnetického prostředí na systémy se vztahem k bezpečnosti; c) netýká se přímého ne-bezpečí elektromagnetických polí na živé tvory ani se netýká porušení izolace se vztahem k bezpečnosti nebo jiných mechanismů, kdy může být osoba vystavena elektrickému nebezpečí.

Obsah

ČSN EN 60839-11-32 This part of IEC 60839 defines the Web services interface for electronic access control systems. This includes listing electronic access control system components, their logical composition, monitoring their states and controlling them. It also includes a mapping of mandatory and optional requirements as per IEC 60839-11-1. This document applies to physical security only. Physical security prevents unauthorized personnel, attackers or accidental intruders from physically accessing a building, room, etc. Web services usage and device management functionality are outside of the scope of this document. Refer to IEC 60839-11-31 for more information. This document does not in any way limit a manufacturer to add other protocols or extend the protocol defined here. For rules on how to accomplish this refer to IEC 60839­11­31.