Normy

Obsah

ČSN EN 16573 This European Standard specifies the laboratory test methods and test requirements for aerodynamic, energy rating and acoustic performance, of multifunctional balanced units intended for use in a single dwelling. In the case of units consisting of several parts, this standard applies only to those designed and supplied as a complete package with the mount instructions. It covers units that contain at least, within one or more casing: - supply and exhaust air fans; - air filters - common control system; and one or more of the additional components: - air to water heat pump; - air to air heat pump; - air-to-air heat exchanger. Units including only an air to air heat exchanger and/or an exhaust air to supply air heat pump are covered by EN 13141-7. A non-exhaustive list of possible configurations of multifunctional units covered by this standard is given in Clause 5. The standard does not cover the thermal aspects of humidity transfer in the air-to-air heat exchanger. This standard does not deal with non-ducted units on supply and extract air side. This standard does not deal with collective units (centralized or semi-centralized systems) These multifunctional balanced units can be connected to ground heat exchanger for air preheating, solar collector or other heating systems. This standard does not cover the testing with these additional components. This standard does not cover units including combustion engine driven compression heat pumps and sorption heat pump.

Obsah

ČSN EN 1539 Tato norma pokrývá všechna významnější nebezpečí, nebezpečné situace a nebezpečné události týkající se sušiček a pecí pro uvolňování hořlavých látek odpařováním nebo sušením nátěrových materiálů. V této normě nejsou pokryta specifická významná nebezpečí, která jsou spojena s použitím takovýchto strojů pro potraviny nebo farmaceutické výrobky. Tato norma platí pouze pro stroje, které jsou používány pro stanovené účely a v podmínkách předpokládaných poruch specifikovaných výrobcem (viz kapitola 4). Pro pece a sušičky, ve kterých se uvolňují hořlavé látky odpařováním a sušením nátěrových materiálů, a ve kterých za žádných okolností není koncentrace hořlavých látek vyšší než 3 % LEL, může být místo této normy použita EN 746-1 a EN 746-2. Tato norma neplatí pro: - pece pro vytvrzování kovů; - strojní zařízení pro smaltování; - přenosná topidla používaná pro sušení (například infračervená topidla, horkovzdušná topidla, fény); - strojní zařízení pro regeneraci rozpouštědel; - strojní zařízení pro destilaci a/nebo refrakci; - systémy pro chemické čistění textilu. Tato norma neplatí pro strojní zařízení, které byly vyrobeny před datem vydání této evropské normy.

Obsah

ČSN ETSI EN 300 422-2 V2.1.1 The present document specifies the technical characteristics and methods of measurement for the following types of equipment: a) Assistive Listening Devices (ALDs); b) Radio Microphones; c) In-Ear Monitoring Systems; d) Wireless Multichannel Audio Systems (WMAS); e) Tour Guide Systems; with Class B receivers which have reduced performance requirements with respect to sensitivity, adjacent channel selectivity, and receiver blocking compared to those with Class A receivers. It does not necessarily include all the characteristics that may be required by a user, nor does it necessarily represent the optimum performance achievable. Equipment with Class B receivers will support the operation of fewer wireless audio channels in a given amount of spectrum than Class A receivers. The present document applies to equipment operating on radio frequencies up to 3 GHz (as shown in table 1) using analogue, digital and hybrid (using both analogue and digital) modulation. The maximum power recommended for equipment covered by this multi-part deliverable is 250 mW for radio microphones and 10 mW for ALDs. An exception to this are the Public Hearing Aids defined in the CEPT Report 004 [i.7] and subsequent EC Decision 2005/928/EC [i.9] and EC Decision 2006/771/EC [i.8] on the ex ERMES band (169,4 MHz to 169,8125 MHz) where 500 mW is defined. The present document covers the essential requirements of Article 3.2 of Directive 2014/53/EU under the conditions identified in annex A. The present document also covers radio microphones used in the 863 MHz to 865 MHz band, with a maximum power of 10 mW. Electromagnetic Compatibility (EMC) requirements are covered by ETSI EN 301 489 9 [i.4]. National regulations on: 1) maximum power output; 2) licensing status; will take precedence or those detailed in the latest version of: " EC Decision 2005/928/EC [i.9]; " ECC/DEC/(05)02 [i.10]; " the EC SRD Decision [i.8]; or " CEPT/ERC/REC 70-03 [i.6], annex 10 (see http://www.erodocdb.dk/); " EC Decision 2014/641/EU [i.11]. Unless otherwise stated in the EC SRD Decision, ECC Decision or National Interfaces, Radio Microphones can be subject to individual licence.

Obsah

ČSN ETSI EN 300 422-3 V2.1.1 The present document specifies the technical characteristics and methods of measurement for the following types of equipment: 1) Assistive Listening Devices; 2) Radio Microphones; 3) In-ear Monitoring Systems; 4) WMAS (Wireless Multichannel Audio Systems; 5) Tour Guide Systems; with Class C receivers which have significantly reduced performance requirements with respect to sensitivity, adjacent channel selectivity, and receiver blocking compared to those with Class A receivers. It does not necessarily include all the characteristics that may be required by a user, nor does it necessarily represent the optimum performance achievable. Equipment with Class C receivers will support the operation of fewer wireless audio channels in a given amount of spectrum than Class A or Class B receivers. The present document applies to equipment operating on radio frequencies up to 3 GHz (as shown in table 1) using analogue, digital and hybrid (using both analogue and digital) modulation. The maximum power recommended for equipment covered by this multi-part deliverable is 250 mW for radio microphones and 10 mW for ALDs. An exception to this are the Public Hearing Aids defined in the CEPT Report 004 [i.7] and subsequent EC Decision 2005/928/EC [i.9] and EC Decision 2006/771/EC [i.8] on the ex ERMES band (169,4 MHz to 169,8125 MHz) where 500 mW is defined. The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU under the conditions identified in annex A. The present document also covers radio microphones used in the 863 MHz to 865 MHz band, with a maximum power of 10 mW. Electromagnetic Compatibility (EMC) requirements are covered by ETSI EN 301 489 9 [i.4]. National regulations on: 1) maximum power output; 2) licensing status; will take precedence or those detailed in the latest version of: - EC Decision 2005/928/EC [i.9]; - ECC/DEC/(05)02 [i.10]; - the EC SRD Decision [i.8]; or - CEPT/ERC/REC 70-03 [i.6], annex 10 (see http://www.erodocdb.dk/); - EC Decision 2014/641/EU [i.11]. Unless otherwise stated in the EC SRD Decision, ECC Decision or National Interfaces, Radio Microphones can be subject to individual licence.

Obsah

ČSN ETSI EN 300 720 V2.1.1 The present document specifies the minimum technical characteristics required for UHF on board vessels radio equipment and systems operating on frequencies allocated to the maritime mobile services by the ITU Radio Regulations [i.1]. The present document contains requirements to demonstrate that "... Radio equipment shall be so constructed that it both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference" [i.3]. In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the Directive 2014/53/EU [i.3] may apply to equipment within the scope of the present document.

Obsah

ČSN ETSI EN 301 025 V2.2.1 The present document covers the minimum requirements for general communication for shipborne fixed installations using a VHF radiotelephone operating in certain frequency bands allocated to the maritime mobile service using either 25 kHz or 25 kHz and 12,5 kHz channels and associated equipment for DSC - class D. The present document does not cover requirements for the integrated GNSS receiver providing locating function. These requirements include the relevant provisions of the ITU Radio Regulations, appendix 18 [1], Recommendation ITU R M.493-14 [3] (where class D is defined), Recommendation ITU R M.825 3 [i.4] and incorporate the relevant guidelines of the IMO as detailed in IMO Circular MSC/Circ-803 [i.1]. The present document also specifies technical characteristics, methods of measurement and required test results. The present document covers the essential requirements of article 3.2 and article 3.3(g) of Directive 2014/53/EU [i.3] under the conditions identified in annex A.

Obsah

ČSN EN 16682 This European Standard is aimed to inform and assist users in the choice and use of the most appropriate method to obtain reliable measurements of the moisture content, or water content, in wood and masonry (including brickwork, stonework, concrete, gypsum, mortars, etc.) in the specific case of the built cultural heritage. It provides a basic framework to take and interpret this kind of measurements on the above cultural heritage materials that have undergone weathering, pest attack, salt migration or other transformations over time. It specifies four absolute methods (i.e. gravimetric, Karl Fischer titration, azeotropic distillation and calcium carbide); explains their characteristics, pros and cons, and gives specifications for the transformation of readings into the same unit to make measurements taken with different methods comparable. It specifies the three principal relative methods (i.e. electrical resistance, capacitance, and relative humidity in equilibrium with the material), pointing out their characteristics and uncertainties when used in the field of cultural heritage. In addition, it provides an informative overview of ten other relative methods, their characteristics, pros and cons. It gives specifications for the calibration of the various methods. It also compares the above methods in relation to their accuracy, sampling requirement, sample size, laboratory or field use, and other problems encountered in the field of cultural heritage to prevent instrument misuse, reduce uncertainties and avoid reading misinterpretation.

Obsah

ČSN EN 61005 ed. 2 Tato mezinárodní norma je použitelná pro sestavy navržené k měření (příkonu) prostorového dávkového ekvivalentu neutronového záření v polích, které obsahují neutrony s energií pod 20 MeV a které obsahují alespoň: detekční sestavu, která například může sestávat z detekční sondy pro tepelné neutrony a uspořádání media obklopujícího detektor, které moderuje a absorbuje neutrony; měřící sestavu s displejem pro měřenou veličinu, která může být zahrnuta do jedné sestavy s detektorem, nebo připojena pomocí ohebného kabelu. Přístroje s rozsahem energie nad 20 MeV jsou pokryty touto normou. Jestliže přístroj též poskytuje indikaci neutronové dávky, musí splňovat požadavky na neutronovou dávku uvedené v této normě. V této normě nejsou specifikovány žádné požadavky pro provoz sestav v pulzujícím poli. Sestavy navržené pro splnění této normy nemusí být vhodné pro taková pole.

Obsah

ČSN EN ISO 15216-1 This document specifies a method for the quantification of levels of HAV and norovirus genogroup I (GI) and II (GII) RNA, from test samples of foodstuffs (soft fruit, leaf, stem and bulb vegetables, bottled water, BMS) or food surfaces. Following liberation of viruses from the test sample, viral RNA is then extracted by lysis with guanidine thiocyanate and adsorption on silica. Target sequences within the viral RNA are amplified and detected by real-time RT-PCR. This method is not validated for detection of the target viruses in other foodstuffs (including multi-component foodstuffs), or any other matrices, nor for the detection of other viruses in foodstuffs, food surfaces or other matrices.

Obsah

ČSN P CEN ISO/TS 17574 This document provides guidelines for preparation and evaluation of security requirements specifications, referred to as Protection Profiles (PP) in ISO/IEC 15408 (all parts) and in ISO/IEC TR 15446. By Protection Profile (PP), it means a set of security requirements for a category of products or systems that meet specific needs. A typical example would be a PP for On-Board Equipment (OBE) to be used in an EFC system. However, the guidelines in this document are superseded if a Protection Profile already exists for the subsystem in consideration. The target of evaluation (TOE) for EFC is limited to EFC specific roles and interfaces as shown in Figure 1. Since the existing financial security standards and criteria are applicable to other external roles and interfaces, they are assumed to be outside the scope of TOE for EFC. The security evaluation is performed by assessing the security-related properties of roles, entities and interfaces defined in security targets (STs), as opposed to assessing complete processes which often are distributed over more entities and interfaces than those covered by the TOE of this document. NOTE: Assessing security issues for complete processes is a complimentary approach, which may well be beneficial to apply when evaluating the security of a system.

Obsah

ČSN EN 62325-351 ed. 2 Tato mezinárodní norma je součástí souboru IEC 62325 pro komunikaci v rámci deregulovaného trhu s energií. Základním úkolem souboru norem IEC 62325 je vytvoření norem, které budou usnadňovat integraci aplikačního softwaru pro trh, vyvinutého nezávisle různými prodejci, do systému správy trhu, mezi systémy správy trhu a systémy aktérů na trhu. Toho je docíleno pomocí definice výměny zpráv, která umožňuje těmto aplikacím nebo systémům přístup k veřejným datům a výměnu informací nezávisle na tom, jak jsou tyto informace vnitřně znázorněny. Tato část IEC 62325 poskytuje specifikace profilu evropského typu trhu, který podporuje trhy s elektrickou energií vytvořené pro evropský typ trhu. Tyto tržní procesy jsou založeny na evropských nařízeních a na konceptech přístupu třetích stran a zónových trhů. Tato část IEC 62325 byla původně založena na práci Evropských provozovatelů přenosových soustav (ETSO) a následně na práci Sdružení evropských provozovatelů elektroenergetických přenosových soustav (ENTSO-E).

Obsah

ČSN EN 16730 Tato evropská norma navazuje na soubor norem EN 13230 v případě, že na pražce příčné nebo výhybkové jsou instalovány podpražcové podložky (USP). USP je pružná vrstva upevněná na ložné ploše pražců příčných nebo výhybkových. Tato norma se vztahuje na systém skládající se z betonových příčných nebo výhybkových pražců a podpražcové podložky.