Normy

Obsah

ČSN EN ISO 18674-7 (72 1012) This document specifies the measurement of strain by means of strain gauges and strainmeters carried out for geotechnical monitoring. General rules of performance monitoring of the ground, of structures interacting with the ground, of geotechnical fills and of geotechnical works are presented in ISO 18674-1. This document is applicable to: performance monitoring of - 1-D structural members such as piles, struts, props and anchor tendons; - 2-D structural members such as foundation plates, sheet piles, diaphragm walls, retaining walls and shotcrete/concrete tunnel linings; - 3-D structural members such as gravity dams, earth- and rock-fill dams, embankments and reinforced soil structures; checking geotechnical designs and adjustment of construction in connection with the observational design procedure; evaluating stability during or after construction. With the aid of a stress-strain relationship of the material, strain data can be converted into stress and/or forces (for 1-D members; see ISO 18674-8) or stresses (for 2-D and 3-D members, see ISO 18674-5). NOTE - This document fulfils the requirements for the performance monitoring of the ground, of structures interacting with the ground and of geotechnical works by the means of strain measuring instruments as part of the geotechnical investigation and testing in accordance with References [1] and [2].

Obsah

ČSN EN 1793-4 This document specifies a test method for determining the intrinsic characteristics of sound diffraction of added devices installed on the top of road traffic noise reducing devices. The test method prescribes measurements of the sound pressure level at several reference points near the top edge of a road traffic noise reducing device with and without the added device installed on its top. The effectiveness of the added device is calculated as the difference between the measured values with and without the added devices, correcting for any change in height (the method specified gives the acoustic benefit over a simple barrier of the same height; however, in practice the added device can raise the height and this could provide additional screening depending on the source and receiver positions). This document is applicable to: - the preliminary qualification, outdoors or indoors, of added devices to be installed on road traffic noise reducing devices; - the determination of sound diffraction index difference of added devices in actual use; - the comparison of design specifications with actual performance data after the completion of the construction work; - the verification of the long-term performance of added devices (with a repeated application of the method); - the interactive design process of new products, including the formulation of installation manuals. The test method can be applied both in situ and on samples purposely built to be tested using the method described here. Results are expressed as a function of frequency, in one-third octave bands between 100 Hz and 5 kHz. If it is not possible to get valid measurements results over the whole frequency range indicated, the results are given in the restricted frequency range and the reasons of the restriction(s) are clearly reported. A single-number rating is calculated from frequency data. For indoor measurements, see Annex D.

Obsah

ČSN EN 18087 This document specifies requirements for dosing systems for chlorine dioxide generation according to the chlorite-chlorine gas process, the chlorite-acid process and the chlorite-sodium peroxodisulphate process, which are used for the disinfection and oxidation of substances in water. The chlorine dioxide (ClO2) solution is produced on site (in situ) by automated mixing of chemical precursors.

Obsah

ČSN EN ISO 17510 This document specifies requirements for masks and accessories, including any connecting element, that are required to connect the patient-connection port of sleep apnoea breathing therapy equipment to a patient for the application of sleep apnoea breathing therapy (e.g. nasal masks, exhaust ports and headgear). This document applies to masks and their accessories used to connect sleep apnoea breathing therapy equipment to the patient. The requirements in this document take priority over the requirements in ISO 18190. This document does not cover oral appliances. NOTE - This document has been prepared to address the relevant essential principles[14] and labelling principles[15] of the International Medical Devices Regulators Forum (IMDRF) as indicated in Annex I.

Obsah

ČSN EN ISO/ASTM 52948 This document specifies the classification of imperfections possibly generated during an additive manufacturing process by PBF-LB (laser beam powder bed fusion) or PBF-EB (electron beam powder bed fusion) for metallic parts. This document also indicates the most probable causes of the formation of imperfections and includes illustrations. This can be extended to other additive manufacturing process categories, nevertheless, the indication of probable causes is process specific. Acceptance criteria and dimensional description or scale for imperfections are not included in this document.

Obsah

ČSN EN ISO 17507-1 This document specifies the MNC method for the calculation of the methane number of a gaseous fuel, using the composition of the gas as sole input for the calculation. This document applies to natural gas (and biomethane) and their admixtures with hydrogen.

Obsah

ČSN EN ISO 11929-2 The ISO 11929 series specifies a procedure, in the field of ionizing radiation metrology, for the calculation of the "decision threshold", the "detection limit" and the "limits of the coverage interval" for a non-negative ionizing radiation measurand when counting measurements with preselection of time or counts are carried out. The measurand results from a gross count rate and a background count rate as well as from further quantities on the basis of a model of the evaluation. In particular, the measurand can be the net count rate as the difference of the gross count rate and the background count rate, or the net activity of a sample. It can also be influenced by calibration of the measuring system, by sample treatment and by other factors. ISO 11929 has been divided into four parts covering elementary applications in ISO 11929-1, advanced applications on the basis of the GUM Supplement 1 in this document, applications to unfolding methods in ISO 11929-3, and guidance to the application in ISO 11929-4. ISO 11929-1 covers basic applications of counting measurements frequently used in the field of ionizing radiation metrology. It is restricted to applications for which the uncertainties can be evaluated on the basis of the ISO/IEC Guide 98-3 (JCGM 2008). In ISO 11929-1:2025, Annex A, the special case of repeated counting measurements with random influences is covered, while measurements with linear analogous ratemeters are covered in ISO 11929-1:2025, Annex B. ISO 11929-3 deals with the evaluation of measurements using unfolding methods and counting spectrometric multi-channel measurements if evaluated by unfolding methods, in particular, for alpha- and gamma spectrometric measurements. Further, it provides some advice on how to deal with correlations and covariances. ISO 11929-4 gives guidance to the application of ISO 11929, summarizes shortly the general procedure and then presents a wide range of numerical examples. Information on the statistical roots of ISO 11929 and on its current development may be found elsewhere. ISO 11929 also applies analogously to other measurements of any kind especially if a similar model of the evaluation is involved. Further practical examples can be found, for example, in ISO 18589, ISO 9696, ISO 9697, ISO 9698, ISO 10703, ISO 7503, ISO 28218 and ISO 11665.

Obsah

ČSN EN ISO 11929-3 The ISO 11929 series specifies a procedure, in the field of ionizing radiation metrology, for the calculation of the "decision threshold", the "detection limit" and the "limits of the coverage interval" for a non-negative ionizing radiation measurand when counting measurements with preselection of time or counts are carried out. The measurand results from a gross count rate and a background count rate as well as from further quantities on the basis of a model of the evaluation. In particular, the measurand can be the net count rate as the difference of the gross count rate and the background count rate, or the net activity of a sample. It can also be influenced by calibration of the measuring system, by sample treatment and by other factors. ISO 11929 has been divided into four parts covering elementary applications in ISO 11929-1, advanced applications on the basis of the ISO/IEC Guide 98-3:2008/Suppl 1:2008 in ISO 11929-2, applications to unfolding methods in this document, and guidance to the application in ISO 11929-4. ISO 11929-1 covers basic applications of counting measurements frequently used in the field of ionizing radiation metrology. It is restricted to applications for which the uncertainties can be evaluated on the basis of the ISO/IEC Guide 98-3 (JCGM 2008). In ISO 11929-1:2025, Annex A, the special case of repeated counting measurements with random influences is covered, while measurements with linear analogous ratemeters, are covered in ISO 11929-1:2025, Annex B. This document deals with the evaluation of measurements using unfolding methods and counting spectrometric multi-channel measurements if evaluated by unfolding methods, in particular, for alpha- and gamma spectrometric measurements. Further, it provides some advice on how to deal with correlations and covariances. ISO 11929-4 gives guidance to the application of the ISO 11929 series, summarizes shortly the general procedure and then presents a wide range of numerical examples. ISO 11929 Standard also applies analogously to other measurements of any kind especially if a similar model of the evaluation is involved. Further practical examples can be found, for example, in ISO 18589, ISO 9696, ISO 9697, ISO 9698, ISO 10703, ISO 7503, ISO 28218, and ISO 11665.

Obsah

ČSN EN ISO 11929-1 The ISO 11929 series specifies a procedure, in the field of ionizing radiation metrology, for the calculation of the "decision threshold", the "detection limit" and the "limits of the coverage interval" for a non-negative ionizing radiation measurand when counting measurements with preselection of time or counts are carried out. The measurand results from a gross count rate and a background count rate as well as from further quantities on the basis of a model of the evaluation. In particular, the measurand can be the net count rate as the difference of the gross count rate and the background count rate, or the net activity of a sample. It can also be influenced by calibration of the measuring system, by sample treatment and by other factors. ISO 11929 has been divided into four parts covering elementary applications in this document, advanced applications on the basis of the ISO/IEC Guide 3-1 in ISO 11929-2, applications to unfolding methods in ISO 11929-3, and guidance to the application in ISO 11929-4. This document covers basic applications of counting measurements frequently used in the field of ionizing radiation metrology. It is restricted to applications for which the uncertainties can be evaluated on the basis of the ISO/IEC Guide 98-3 (JCGM 2008). In Annex A, the special case of repeated counting measurements with random influences is covered, while measurements with linear analogous ratemeters are covered in Annex B. ISO 11929-2 extends the former ISO 11929:2010 to the evaluation of measurement uncertainties according to the ISO/IEC Guide 98-3:2008/Suppl 1:2008. ISO 11929-2 also presents some explanatory notes regarding general aspects of counting measurements and on Bayesian statistics in measurements. ISO 11929-3 deals with the evaluation of measurements using unfolding methods and counting spectrometric multi-channel measurements if evaluated by unfolding methods, in particular, for alpha- and gamma spectrometric measurements. Further, it provides some advice on how to deal with correlations and covariances. ISO 11929-4 gives guidance to the application of the ISO 11929 series, summarizes shortly the general procedure and then presents a wide range of numerical examples. Information on the statistical roots of ISO 11929 and on its current development may be found elsewhere. The ISO 11929 series also applies analogously to other measurements of any kind especially if a similar model of the evaluation is involved. Further practical examples can be found, for example, in ISO 18589, ISO 9696, ISO 9697, ISO 9698, ISO 10703, ISO 7503, ISO 28218 and ISO 11665.

Obsah

ČSN EN ISO 5530-1 This document specifies a method using a farinograph for the determination of the water absorption of flours and the mixing behaviour of doughs made from them by a constant flour mass procedure or by a constant dough mass procedure. The method is applicable to experimental and commercial flours from wheat (Triticum aestivum L.).

Obsah

ČSN EN 12767+A1 Tento dokument specifikuje postupy zkoušek funkčních charakteristik pro stanovení pasivních bezpečnostních vlastností podpěrných konstrukcí, jako jsou sloupy osvětlení, sloupky a další podpěrné systémy značek, konstrukční prvky, základy/podklad, oddělitelné výrobky a jakékoli další komponenty používané k podpěře konkrétní části vybavení na okraji silnice. Tento dokument poskytuje společný základ pro zkoušení nárazů vozidel do podpěrných konstrukcí silničních zařízení. Tento dokument se nevztahuje na záchytné systémy

Obsah

ČSN EN ISO 18227 This document specifies the procedure for a quantitative determination of major and trace element concentrations in homogeneous solid waste, soil, soil-like material and sludge by energy dispersive X-ray fluorescence (EDXRF) spectrometry or wavelength dispersive X-ray fluorescence (WDXRF) spectrometry using a calibration with matrix-matched standards. This document is applicable for the following elements: Na, Mg, Al, Si, P, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Se, Br, Rb, Sr, Y, Zr, Nb, Mo, Ag, Cd, Sn, Sb, Te, I, Cs, Ba, Ta, W, Hg, Tl, Pb, Bi, Th and U. Concentration levels between a mass fraction of approximately 0,000 1 % and 100 % can be determined depending on the element and the instrument used. An optional XRF screening method for solid and liquid material as waste, sludge and soil is added in Annex A which provides a total element characterization at a semi-quantitative level, where the calibration is based on matrix-independent calibration curves, previously set up by the manufacturer.