Normy

Obsah

ČSN EN 16585-2 This document describes the specific 'Design for PRM use' requirements applying to rolling stock and the assessment of those requirements. The following applies to this document: - The definitions and requirements describe specific aspects of 'Design for PRM use' required by persons with disabilities and persons with reduced mobility as defined in the PRM TSI. - This document defines elements which are universally valid for obstacle-free travelling relating to elements for sitting, standing and moving. The definitions and requirements of this document are to be used for rolling stock applications. - This document only refers to aspects of accessibility for PRM passengers; It does not define general requirements and general definitions. - This document assumes that the rolling stock is in its defined operating condition. - Where minimum or maximum dimensions are quoted these are absolute NOT nominal requirements. The 'Equipment and components' standard is written in three parts: - Part 1 contains: - toilets. - This document is Part 2 and contains: - handholds; - seats; - wheelchair spaces. - Part 3 contains: - clearways; - internal doors.

Obsah

ČSN EN 16585-1 This document describes the specific 'Design for PRM use' requirements applying to rolling stock and the assessment of those requirements. The following applies to this document: - The definitions and requirements describe specific aspects of 'Design for PRM use' required by persons with disabilities and persons with reduced mobility as defined in the PRM TSI. - This document defines elements which are universally valid for obstacle-free travelling relating to toilets. The definitions and requirements of this document are to be used for rolling stock applications. - This document only refers to aspects of accessibility for PRM passengers; it does not define non-PRM related requirements and definitions. - This document assumes that the rolling stock is in its defined operating condition. - Where minimum or maximum dimensions are quoted these are absolute NOT nominal requirements. The 'Equipment and Components' standard is written in three parts: - this document is Part 1 and contains: - toilets. - Part 2 contains: - handholds; - seats; - wheelchair spaces. - Part 3 contains: - clearways; - internal doors.

Obsah

ČSN EN 17860-6 This document applies to the transportation of passengers in a forward- and/or rearward-facing position on a carrier cycle as defined in the EN 17860 series, except for Part 7 (carrier cycle trailers). This document does not apply to the transportation of children in a child seat that is tested according to EN 14344:2022. This document applies to the intended riding purpose commuting and leisure with moderate effort, in accordance with EN 17406:2020+A1:2021. NOTE - Some European countries have speci

Obsah

ČSN EN IEC 61643-41 This document, together with IEC 61643-01, is applicable to devices for surge protection against indirect and direct effects of lightning or other transient overvoltages. These devices are intended to be connected to DC power circuits and equipment rated up to 1 500 V DC. Performance and safety requirements, tests and ratings are specified in this document. These devices contain at least one nonlinear component and are intended to limit surge voltages and divert surge currents. The test requirements provided by this document are based on the assumption that the SPD is connected to a DC power circuit fed by a power source providing a linear voltage-current characteristic. When the SPD is to be connected to a different kind of source, careful consideration is required. This mainly applies with regard to system and fault conditions to be expected in such a system (e.g. expected short circuit current, TOV-stresses).

Obsah

ČSN EN IEC 60068-2-2 ed. 2 This part of IEC 60068 specifies dry heat temperature tests that are applicable to non-heat-dissipating and heat-dissipating specimens, to determine the ability of components, equipment or other articles to be used, transported or stored at high temperature. This document is applicable to energized as well as non-energized specimens that normally achieve temperature stability during the test. The specimens can be subject to test in packed condition (to simulate transportation and storage) or in unpacked condition (to simulate use). This document does not specify tests to determine the impact of temperature changes on specimens.

Obsah

ČSN EN IEC 60068-2-1 ed. 3 This part of IEC 60068 specifies temperature tests at low temperatures, generally referred to as "cold tests", that are applicable to non-heat-dissipating and heat-dissipating specimens, to determine the ability of components, equipment, or other articles to be used, transported or stored at low temperature. This document is applicable to energized as well as non-energized specimens that normally achieve temperature stability during the test. The specimens can be subject to test in packed condition (to simulate transportation and storage) or in unpacked condition (to simulate use). This document does not specify tests to determine the impact of temperature changes on specimens.

Obsah

ČSN EN IEC 61326-2-6 ed. 4 This International Standard applies to the basic safety and essential performance of in vitro diagnostic medical electrical equipment (ivd mee). This part of IEC 61326 applies to the basic safety and essential performance of ivd mee in the presence of electromagnetic disturbances and to electromagnetic disturbances emitted by ivd mee.

Obsah

ČSN EN IEC 60931-1 ed. 2 This part of IEC 60931 is applicable to both non-self-healing capacitor units and non-self-healing capacitor banks intended to be used, particularly, for power-factor correction of AC power systems having a rated voltage up to and including 1 000 V and frequencies 15 Hz to 60 Hz. This document also applies to capacitors intended for use in power filter circuits. Additional definitions, requirements, and tests for filter capacitors are given in Annex A. Accessories such as insulators, switches, instrument transformers, fuses, etc., are to be in accordance with the relevant IEC standards. The purpose of this document is to formulate uniform rules regarding performances, testing and rating, to formulate specific safety rules and to provide a guide for installation and operation.

Obsah

ČSN EN IEC 60730-2-6 ed. 4 This clause of Part 1 is replaced by the following: This document applies to automatic electrical pressure sensing controls - for use in, on, or in association with equipment for household appliance and similar use; NOTE 1 - Throughout this document, the word "equipment" means "appliance and equipment" and "controls" means "pressure sensing controls". - for building automation within the scope of ISO 16484 series and IEC 63044 series (HBES/BACS); EXAMPLE 1 - Independently mounted automatic electrical pressure sensing controls, controls in smart grid systems and controls for building automation systems within the scope of ISO 16484-2. - for equipment that is used by the public, such as equipment intended to be used in shops, offices, hospitals, farms and commercial and industrial applications; EXAMPLE 2 - Automatic electrical pressure sensing controls for commercial catering, heating and air-conditioning equipment. - that are smart enabled automatic electrical pressure sensing controls; EXAMPLE 3 - Smart grid automatic electrical pressure sensing controls, remote interfaces/control of energy-consuming equipment including computer or smart phone. - that are AC or DC powered controls with a rated voltage not exceeding 690 V AC or 600 V DC; - used in, on, or in association with equipment that use electricity, gas, oil, solid fuel, solar thermal energy, etc., or a combination thereof; - utilized as part of a control system or controls which are mechanically integral with multifunctional controls having non-electrical outputs; - using NTC or PTC thermistors and to discrete thermistors, requirements for which are contained in Annex J; - that are mechanically or electrically operated, responsive to or controlling a pressure or vacuum; - as well as manual controls when such are electrically and/or mechanically integral with automatic controls. NOTE 2 - Requirements for manually actuated mechanical switches not forming part of an automatic control are contained in IEC 61058-1-1. This document is also applicable to individual pressure sensing controls utilized as part of a control system or pressure sensing controls which are mechanically integral with multi-functional controls having non-electrical outputs. This document is also applicable to pressure sensing controls for appliances within the scope of IEC 60335-1. This document applies to - the inherent safety of pressure sensing controls, and - functional safety of pressure sensing controls and safety related systems, - pressure sensing controls where the performance (for example the effect of EMC phenomena) of the product can impair the overall safety and performance of the controlled system, - the operating values, operating times, and operating sequences where such are associated with equipment safety. This document specifies the requirements for construction, operation and testing of automatic electrical controls used in, on, or in association with an equipment. This document does not - apply to pressure sensing controls intended exclusively for industrial process applications unless explicitly mentioned in the relevant part 2 or the equipment standard. However, this document can be applied to evaluate automatic electrical controls intended specifically for industrial applications in cases where no relevant safety standard exists; - take into account the response value of an automatic action of a pressure sensing control, if such a response value is dependent upon the method of mounting the control in the equipment. Where a response value is of significant purpose for the protection of the user, or surroundings, the value defined in the appropriate equipment standard or as determined by the manufacturer will apply; - address the integrity of the output signal to the network devices, such as interoperability with other devices unless it has been evaluated as part of the control system. This document contains requirements for electrical features of pressure sensing controls and requirements for mechanical features that affect their intended operation. NOTE - Subclause 20.101, as it pertains to gas and/or oil controls, is under consideration pending review or revision of ISO 22967, ISO 22968 and ISO 23550, if applicable. In general, these pressure sensing controls are integrated or incorporated with the equipment or are intended to be integrated in, or on the equipment. This document also covers these controls when they are independently mounted. In-line cord controls are not covered by this document.

Obsah

ČSN EN IEC 60730-2-23 This part of IEC 60730 applies to the safety of electrical, electro-mechanical and electronic sensors including sensing elements and any conditioning circuitry. Sensors covered under the scope of this document serve only to transform an activating quantity into a usable output and do not perform a control operation as defined in IEC 60730-1. This document applies to sensors in so far as defining the reliability and accuracy of their inherent operating characteristics and corresponding response under normal and abnormal conditions within the sensor. Sensors, as defined herein, are used in or as part of an automatic electrical control or as independently mounted devices in connection with controls and control systems. The use of this document for other applications in which sensors are used is possible provided that the appropriate safety is maintained as defined by the end product standard. This document applies to discrete sensors constructed of, but not limited to, conductive or semiconductive substrate, for the detection of activating quantities such as voltage, current, temperature, pressure, humidity, light (e.g. optical), gasoline vapours, and the like. This document applies to sensing element(s) as well as any electronic hardware, software, or other conditioning circuits that are inherent to the sensor and relied upon to reliably transform the input signal into a useable response signal (output) for functional safety purposes. Conditioning circuits that are inseparable from the control for which the sensing element relies upon to perform its desired function are evaluated by the requirements of the relevant control Part 2 standard and/or IEC 60730-1. Throughout this document, whenever it is indicated that the IEC 60730-1 requirements are applicable, the term "control(s)", is replaced by the term "sensor(s)", and the term "equipment" is replaced by the term "control", as they are used in IEC 60730-1, respectively, unless otherwise specified herein. This document does not apply to sensors explicitly described in another relevant part 2 of the IEC 60730 series.

Obsah

ČSN EN IEC 63002 ed. 3 This document defines common charging interoperability guidelines for power sources (external power supplies (EPSs) and other Sources) used with computing and consumer electronics devices that implement IEC 62680 1 3 (USB Type-CR Cable and Connector Specification).

Obsah

ČSN EN ISO/IEC 27706 This document specifies requirements and provides guidance for bodies providing audit and certification of a privacy information management system (PIMS) according to ISO/IEC 27701, in addition to the requirements contained within ISO/IEC 17021-1. The requirements contained in this document are demonstrated in terms of competence and reliability by bodies providing PIMS certification. The guidance contained in this document provides additional interpretation of these requirements for bodies providing PIMS certification.